'lowercost alternative'

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are engineered to protect boiler tubes, heat exchanger coils, and superheaters from flue gas erosion, fly ash impact, scaling, and corrosion. These shields are widely used in power plants, industrial boilers, and waste heat recovery units to reduce tube wear, extend service life, and improve operational efficiency. Their half-round, semi-cylindrical design ensures easy installation and a secure fit over curved or straight tubes exposed to abrasive gas flow and thermal cycling. SS 430 Half Round Tube Shield for LTSH Tube The SS 430 Half Round Tube Shield is made from ferritic stainless steel grade 430, which provides good oxidation resistance, moderate corrosion protection, and excellent thermal stability. It is particularly suitable for Low Temperature Superheater (LTSH) applications where boiler tubes operate in moderately corrosive environments and are subject to ash deposition and dry gas erosion. With its high chromium content and low carbon levels, SS 430 offers a cost-effective shielding solution for boiler systems requiring dependable surface protection without the need for high nickel alloys. The Low Temperature Superheater (LTSH) is a section in a boiler where saturated steam from the steam drum is superheated to a moderately higher temperature before entering the high-temperature superheater stages. Positioned in areas with relatively lower flue gas temperatures, the LTSH helps improve thermal efficiency and reduces moisture content in steam. Due to constant exposure to abrasive flue gases and ash, LTSH tubes are prone to wear and require protective shielding, such as half round tube shields, to extend service life. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of SS 430 Half Round Tube Shields for LTSH applications, providing durable and economical protection in moderately corrosive and thermally demanding environments. Chemical Composition of SS 430 – Ferritic Stainless Steel • Carbon (C): ≤ 0.12% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Iron (Fe): Balance Applications: Best suited for low-temperature superheater zones and convection areas where oxidation, thermal exposure, and ash erosion are concerns in boiler and steam systems. Uses • Installed on LTSH tubes to prevent scaling, ash abrasion, and flue gas corrosion • Shields tube surfaces in HRSGs, economizers, and convection zones of WHRBs • Used in industrial and utility boilers operating in dry, oxidizing flue gas environments • Suitable for coal, biomass, or oil-fired systems with moderate corrosion potential • Applied where cost-effective surface protection is required without compromising durability Features • Good oxidation resistance – Maintains integrity under sustained thermal exposure • Cost-effective – Offers a lower-cost alternative to austenitic and molybdenum-bearing steels • Custom-fit design – Precision-fabricated to match tube radius, bend geometry, and length • Easy installation – Can be installed using clamp-on, weld-on, or banding techniques • Reduces tube wear – Protects surfaces from erosion, scaling, and soot buildup • Available in multiple dimensions and thicknesses to match application specifications Applications • thermal power plants – Installed on LTSH tube banks for long-term surface protection • waste heat recovery units – Protects return bends and convection tubes from particulate erosion • steam generation systems – Applied to shield tubes in low-temperature flue zones • industrial boilers – Guards against ash impact in biomass or coal-fired heating systems • process boilers – Enhances durability of heat exchange surfaces in oxidizing environments Conclusion The SS 430 Half Round Tube Shield for LTSH Tube by Ladhani Metal Corporation – manufacturer, supplier, and exporter – offers reliable and cost-efficient protection for superheater and boiler tubes in low-temperature, oxidizing environments. Its thermal stability and erosion resistance make it ideal for power and industrial systems where long-term durability and low maintenance are essential. For detailed specifications, sizing options, or technical consultation, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are engineered to provide robust protection for boiler, superheater, and heat exchanger tubes against high-temperature erosion, slag deposition, scaling, and corrosive gas exposure. These shields are essential in power plants, petrochemical systems, and high-heat industrial environments where tubes are vulnerable to rapid degradation due to thermal cycling and particulate flow. The half-round design ensures quick installation over curved or straight tube sections without system disassembly. U Type Inner Half Round Tube Shield The U Type Inner Half Round Tube Shield is specially designed to protect the inner curvature of U-bend tubes, which often experiences high levels of turbulence, localized corrosion, and scaling due to gas redirection and mechanical stress. Inner shields are commonly paired with outer shields for full bend protection and are manufactured in a wide range of stainless steel and high-temperature alloy grades, customized to specific environmental and system requirements. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of U Type Inner Half Round Tube Shields in various material grades, offering tailored protection solutions for high-temperature and corrosive conditions across multiple industries. Available Grades • SS 304 – General-use stainless steel with good corrosion and heat resistance • SS 304L – Low-carbon version for improved weldability and reduced carbide precipitation • SS 316 – Molybdenum-added alloy with excellent resistance to pitting and chlorides • SS 316L – Low-carbon alternative for superior corrosion resistance in welded environments • SS 310 – Austenitic high-temperature steel with excellent oxidation resistance • SS 310S – Low-carbon SS 310 for better thermal fatigue performance • SS 410 – Martensitic stainless steel with good strength and abrasion resistance • SS 420 – High-hardness martensitic grade ideal for erosion-prone zones • SS 430 – Ferritic grade for moderate corrosion and oxidation resistance • 1Cr13 – Martensitic stainless steel offering mechanical protection and heat resistance • 1Cr18Ni9Ti – Titanium-stabilized grade offering resistance to intergranular corrosion • Cr23Ni13 – High-temperature alloy with excellent oxidation and scaling resistance • Cr25Ni20 – High-performance grade for extreme thermal and oxidizing conditions • 1Cr25Ni20Si2 – Heat-resistant alloy with silicon for improved scale resistance • 1Cr20Ni14Si2 – Alloy for thermal fatigue protection and oxidizing environments Applications • Inner arc protection in U-bend tubes of boilers, superheaters, and reheaters • Shielding internal curves of tubes in waste heat recovery boilers (WHRBs) and HRSGs • Corrosion and scale defense for inner tube arcs in petrochemical and steam reforming units • Inner surface protection in furnace coils, reformers, and incinerators • Installed in chemical plants and thermal systems prone to turbulent flue gas exposure Features • Focused inner arc protection – Guards the most corrosion- and scale-prone surface of U-bend tubes • Material flexibility – Available in multiple grades for varied thermal, mechanical, and chemical requirements • Excellent thermal resistance – Withstands extreme temperatures depending on material (up to 1150°C+) • Precise fit – Custom-fabricated to match exact tube dimensions and bend radii • Simple installation – Mounted using clamps, stainless bands, or welding techniques • Dual-shield pairing – Can be combined with outer shields for complete U-bend coverage • Long-lasting performance – Enhances tube reliability and reduces maintenance in high-wear zones Applications • power generation – Protects U-bend inner surfaces in superheaters and economizers from flue gas turbulence • petrochemical plants – Shields inside arcs in reformers and heaters exposed to chlorides and acidic gases • waste heat systems – Installed in HRSGs and WHRBs to prevent slag and oxidation on internal bends • chemical industries – Suitable for reactors and high-temperature exchangers handling corrosive media • cement and metallurgy – Used in systems exposed to flame, dust, and oxidizing atmospheres Conclusion The U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a precision-engineered solution for protecting the inner arc of U-bend tubes against corrosion, scale formation, and thermal damage. Available in a wide range of stainless steels and high-temperature alloys, these shields provide durable, customizable, and easy-to-install protection for critical components in power, chemical, and thermal processing systems. For custom sizes, technical assistance, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are robust, precision-fabricated protective sleeves designed to guard the outer surfaces of tubes in boilers, heat exchangers, incinerators, and high-temperature processing equipment. Engineered to extend the service life of tubes exposed to corrosive gases, abrasive particulates, and elevated temperatures, these shields provide a reliable barrier against mechanical and chemical degradation. The half-round design facilitates easy installation while ensuring a secure, form-fitting layer of defense. 1Cr13 Half Round Tube Shield The 1Cr13 Half Round Tube Shield is a semi-cylindrical component manufactured from martensitic stainless steel containing approximately 13% chromium. Classified under the 1Cr13 grade, this alloy delivers good corrosion resistance, excellent wear performance, and moderate strength at elevated temperatures. It is especially suited for thermal environments that are not extremely oxidizing or carburizing but where erosion and mechanical wear are a concern. With a higher hardness potential through heat treatment and moderate thermal resistance, 1Cr13 shields are ideal for applications involving flue gas exposure, soot-laden atmospheres, and temperature cycling. The shield’s half-round configuration is precision-engineered for optimal tube coverage and long-term durability. It offers a balance of strength, corrosion resistance, and cost-effectiveness, making it suitable for a wide range of industrial processes. Chemical Composition of 1Cr13 – Martensitic Stainless Steel • Carbon (C): 0.15 – 0.20% • Silicon (Si): ≤ 1.00% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Chromium (Cr): 12.0 – 14.0% • Nickel (Ni): ≤ 0.60% • Iron (Fe): Balance Uses • Boiler Tube Protection – Shields tube surfaces from flue gas erosion, ash particle abrasion, and soot buildup in economizers and waterwalls. • Heat Exchanger Tubes – Provides an extra layer of wear resistance in zones prone to mechanical stress and fluid turbulence. • Incinerator and Waste Heat Units – Guards tubes exposed to fluctuating temperatures, slag, and particulate deposits. • Cement Plant Piping – Protects tubing and ducts in kiln exhaust systems from abrasive dust and high flow velocity. • Air Preheaters and Recuperators – Enhances the durability of components subjected to temperature variations and corrosive gases. Features • Moderate Oxidation Resistance – Chromium content enables good performance in mildly oxidizing environments and intermittent exposure to high temperatures. • Wear and Abrasion Resistance – Martensitic structure offers high surface hardness and resistance to mechanical wear. • Heat Treatable – Can be hardened to increase durability and resistance to deformation. • Cost-Effective – Provides a lower-cost alternative to austenitic and superalloy shields for moderate service conditions. • High Dimensional Accuracy – Manufactured with tight tolerances to ensure secure fitment and uniform tube coverage. • Convenient Installation – Half-round shape enables quick mounting through welding or clamping techniques. • Versatile Finishing Options – Supplied with pickled or mechanically polished surfaces to improve corrosion resistance and adhesion. Applications • Power Generation – Used in economizer, preheater, and convection sections of boilers to prevent erosion and fouling. • Chemical and Fertilizer Plants – Protects exposed tube surfaces in systems with moderate chemical exposure. • Metallurgical Furnaces – Shields mechanical and flue components exposed to particulate movement and temperature cycling. • Pulp and Paper Industry – Used in recovery boilers and heat exchangers where corrosion resistance and mechanical strength are both required. • Petrochemical Plants – Applied in lower-temperature zones where scaling and erosion are primary concerns. Conclusion The 1Cr13 Half Round Tube Shield by Ladhani Metal Corporation provides an optimal solution for industrial tube protection in moderate temperature and corrosion environments. Its martensitic stainless steel composition ensures excellent wear resistance, good oxidation stability, and structural strength at a competitive cost. Designed for easy installation and reliable performance, these shields are ideal for various applications in power, process, and heat recovery systems. Custom-built to meet specific dimensions, material thicknesses, and finishing preferences, 1Cr13 tube shields offer dependable service life extension for critical heat transfer equipment. For technical specifications, pricing, or customization inquiries, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-engineered components designed to protect the outer surfaces of boiler tubes, heat exchangers, and industrial piping systems from erosion, scale formation, and thermal fatigue. These shields play a crucial role in minimizing tube failure and improving overall equipment reliability in high-temperature and particulate-laden environments. SS 430 Half Round Tube Shield The SS 430 Half Round Tube Shield is a semi-cylindrical cladding made from ferritic stainless steel grade 430. With good corrosion resistance, excellent oxidation resistance, and superior thermal conductivity, SS 430 is well suited for non-pressurized or moderately corrosive environments. It is particularly effective in flue gas paths and air preheaters where thermal stress and ash erosion can degrade exposed tubes. The half-round geometry ensures easy, secure installation and a consistent protective barrier around the tube's surface, enhancing durability without interfering with system function. Chemical Composition of SS 430 – Ferritic Stainless Steel • Carbon (C): ≤ 0.12% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Nickel (Ni): ≤ 0.75% • Iron (Fe): Balance Uses • Boiler Tube Surface Protection – Shields tubes in low to moderate temperature zones from flue gas corrosion, ash abrasion, and thermal scaling. • Air Preheater Tubing – Guards against dust erosion in regenerative air preheaters and gas-to-air heat transfer zones. • Economizer Tube Protection – Used in downstream sections of boilers where lower temperatures allow for effective use of ferritic steels. • Steam Line Shields – Protects low-pressure steam tubing and condensate lines in systems not requiring austenitic stainless steel grades. • Heat Exchanger Outer Shells – Provides an extra layer of protection in air-cooled or shell-side applications exposed to mechanical wear. Features • Good Oxidation Resistance – Performs reliably in oxidizing conditions up to 815°C, ideal for flue gas exposure and dry ash environments. • Ferritic Structure – Offers better thermal conductivity and resistance to thermal expansion than austenitic grades, reducing distortion risk. • Corrosion Resistance – Resists corrosion from atmospheric moisture, flue gas condensates, and other mildly aggressive compounds. • Cost-Effective – Offers an economical alternative to higher alloy stainless steels in appropriate thermal zones. • Precision Fit – Half-round design enables quick installation and conforms closely to tube diameters for optimal protection. • Surface Finish Options – Supplied in bright annealed, pickled, or passivated finishes based on operational requirements. • Custom Fabrication – Available in a range of wall thicknesses, diameters, and lengths to meet plant-specific installation demands. Applications • Thermal Power Stations – Shields economizer and air preheater tubes from dust-laden exhaust gas erosion and moderate thermal stress. • Cement and Lime Kilns – Used to protect heat recovery and cooler tubes from dry ash abrasion in hot air ducts. • Food Processing Boilers – Applied in steam systems requiring corrosion resistance and thermal control under hygienic conditions. • HVAC and Utility Boilers – Installed in auxiliary boilers where conditions do not require high-alloy materials but demand durability. • Pulp and Paper Mills – Protects lower furnace zone tubes and stack-side economizers from condensate corrosion and soot accumulation. • Sugar and Distillery Plants – Guards process steam and heat recovery tubes from ash and scale in biomass and bagasse-fired units. Conclusion The SS 430 Half Round Tube Shield by Ladhani Metal Corporation is a durable, cost-efficient solution for protecting tubing systems in environments where moderate corrosion resistance, good oxidation behavior, and thermal stability are essential. It is best suited for dry, low to mid-temperature gas flow areas where the mechanical and thermal loads are not extreme. The ferritic stainless steel structure provides a favorable balance of performance and economy, particularly in large-scale power and process plants. With precision manufacturing, tailored dimensions, and reliable service, Ladhani Metal Corporation delivers proven tube protection technology trusted across multiple industries. For custom orders, sizing assistance, or to request a technical quote, please contact Ladhani Metal Corporation.

The DIN 2558 Titanium Flange PN 6 is a precision-engineered component designed to meet the demanding requirements of modern industrial piping systems. Manufactured in compliance with DIN (Deutsches Institut für Normung) standards, these flanges are crafted from high-grade titanium alloys that offer exceptional resistance to corrosion, extreme temperatures, and chemically aggressive environments. Ladhani Metal Corporation is a reliable supplier of these titanium flanges, delivering products that are valued for their durability, lightweight properties, and long-term performance in critical applications. Types: Weld Neck Flange – Provides a strong, leak-proof joint suitable for high-temperature and high-pressure environments. Slip-On Flange – Easy to install, this flange type is welded on both sides and offers a cost-effective solution. Blind Flange – Used to block off the end of a piping system or pressure vessel, ensuring no flow passes through. Threaded Flange – Ideal for systems where welding is not suitable, this flange screws directly onto the pipe. Socket Weld Flange – Designed for small-diameter piping systems, offering a smooth bore and strong welded joint. Titanium Grades & Chemical Composition: Grade 2 Titanium (Commercially Pure): Titanium (Ti): ≥ 98.9% Iron (Fe): ≤ 0.30% Oxygen (O): ≤ 0.25% Carbon (C): ≤ 0.08% Nitrogen (N): ≤ 0.03% Hydrogen (H): ≤ 0.015% Features: Excellent corrosion resistance, good formability, and weldability. Commonly used in marine and chemical environments. Grade 5 Titanium (Ti-6Al-4V): Titanium (Ti): Balance Aluminum (Al): 5.5 – 6.75% Vanadium (V): 3.5 – 4.5% Iron (Fe): ≤ 0.40% Oxygen (O): ≤ 0.20% Carbon (C): ≤ 0.08% Nitrogen (N): ≤ 0.05% Hydrogen (H): ≤ 0.015% Features: High strength, excellent corrosion resistance, and good fatigue resistance. Commonly used in aerospace, marine, and industrial applications. PN 6 Rating: The PN 6 designation refers to a nominal pressure rating of 6 bar (87 psi), making these flanges suitable for medium-pressure applications in both industrial and marine settings. It ensures safe and reliable connections where corrosion and mechanical integrity are of critical importance. Features: Corrosion Resistance: Titanium provides outstanding resistance to saltwater, chlorides, and many acidic environments. High Strength-to-Weight Ratio: Offers strong performance while being significantly lighter than steel-based alternatives. Temperature Resistance: Suitable for use in high-temperature and cryogenic environments. Versatile Applications: Ideal for use in chemical processing, offshore systems, desalination plants, medical and aerospace applications. Easy Fabrication: Good weldability and formability allow for efficient installation and system integration. Longevity: Titanium flanges from Ladhani Metal Corporation are engineered for long service life, reducing maintenance costs and operational downtime. Ladhani Metal Corporation ensures each DIN 2558 titanium flange is manufactured with precision and tested thoroughly to meet the highest international quality standards, delivering performance and value across a wide range of industrial systems. #din2558 #din2558flanges #din2558titaniumflanges #titaniumflanges #flanges

DIN 2544 is a German standard for flanges used in piping systems, detailing dimensions, design, and testing methods. Titanium flanges conforming to this standard are designed for use in high-performance environments that demand excellent strength, corrosion resistance, and low weight. Titanium is known for its excellent corrosion resistance, particularly in environments like seawater, chemical processing, and heat exchangers. DIN 2544 titanium flanges are specifically built to withstand aggressive conditions, including high temperatures and corrosive environments, while offering a lightweight alternative to other materials like stainless steel. Key Features of DIN 2544 Titanium Flanges: Material: Titanium flanges are made from titanium alloys, which are highly resistant to corrosion, oxidation, and erosion. Titanium is also known for its strength-to-weight ratio, being strong yet much lighter than many other metals, including stainless steel. Corrosion Resistance: Titanium flanges are ideal for systems exposed to harsh environments, such as saltwater, acids, and chlorides. They are widely used in marine, chemical, and offshore oil and gas applications. Temperature Resistance: Titanium flanges can operate in high-temperature environments, often up to 600°C (1,112°F) without degrading, depending on the specific titanium alloy used. Pressure Rating (PN 25): These flanges are typically rated for PN 25, meaning they can withstand pressures of up to 25 bar (approximately 362 psi) in a variety of applications. Types of DIN 2544 Titanium Flanges: Weld Neck Flanges: These flanges have a long neck that is welded to the pipe. They are ideal for high-pressure systems and applications requiring a strong, reliable connection. Slip-On Flanges: These flanges slide over the pipe and are then welded in place. They are generally used in systems where welding is easier, and the pressures are lower than those of weld neck flanges. Blind Flanges: Used to seal the ends of piping systems, these flanges have no hole in the center. They are often used for isolation and maintenance purposes. Threaded Flanges: These flanges have internal threads that match threaded pipes. They are convenient when welding is not practical or possible. Socket Weld Flanges: These flanges feature a socket where the pipe is inserted and welded into place. These are often used in smaller-diameter piping systems. Titanium Grades for Flanges: Grade 2 Titanium (Commercially Pure Titanium): Properties: Most commonly used grade, offering excellent corrosion resistance and formability. It has moderate strength and is used in a variety of industries like aerospace, chemical processing, and marine applications. Advantages: Excellent corrosion resistance in both seawater and chemical environments. Grade 5 Titanium (Ti-6Al-4V): Properties: An alloy with 6% aluminum and 4% vanadium, offering higher strength than grade 2 titanium, while still maintaining good corrosion resistance. Common in high-stress, high-temperature environments. Advantages: Used in aerospace, medical devices, and high-performance applications due to its superior strength and durability. Pressure Rating (PN 25): PN 25 indicates that the titanium flanges are rated to handle pressures of up to 25 bar (approximately 362 psi). This pressure class is suitable for medium to high-pressure applications, ensuring the flange can endure significant stress in various piping systems. #din2544 #din2544flanges #din2544titaniumflanges

Product Name: Titanium rod grade 23 Standard: ASTM F136 Material: Gr23 (Gr5 ELI) Unit Price: $30.5 usd/kg- $52.5 usd/kg Application: Medical use Shape: Round Diameter: 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm, 16mm, 20mm etc. Length: 1000mm, 3000mm, 6000mm or as per your request Surface: Bright Product Introduction Product name:Titanium rod grade 23 Material: GR23 Standard: ASTM F136 Diameter: 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm, 16mm, 20mm etc. Length: 1000mm, 3000mm, 6000mm or as per your request Surface: Polishing,Bright Third-Party Tests: BV, SGS, TUV etc. Grade 23 is a higher purity version of Ti 6Al-4V. It can be made into coils, strands, wires or flat wires and is the first choice for any occasion that requires a combination of high strength, light weight, good corrosion resistance and high toughness. It has excellenct damage resistance superior to other alloys. These advantages make Ti 6AL-4V ELI the final dental and medical titanium grade product. Due to its biocompatibility, good fatigue strength and lo mdulus, it can be used in biomedical applications such as implantable parts. Grade 23 can also be used in detailed surgical procedures, such as: • Orthopedic pins and screws • Orthopedic cables • Ligation needles • Surgical staples • Springs • Orthodontic appliances • Joint replacements • Cryogenic containers • Bone fixators Mechanical Properties: Grade Tensile strength, MPa (min) Yield strength, MPa (min) Elongation, %(min) Reduction of Area, %(min) Gr23 828 759 10 15 Chemical Component (ASTM B348) Grade Ti Al V N, max C, max H, max Fe, max O, max Residuals Max each Max total Gr23 Main 5.5-6.5 3.5-4.5 0.03 0.08 0.0125 0.25 0.13 0.1 0.4

ladhani metal corporation is supplier and exporter of GB H0Cr20Ni10Ti sheet , plate , coil , flat bar , circular plate , plate flanges , farma , laser cutting design sheet , waterjet cutting design sheet.GB H0Cr20Ni10Ti is the basic austenitic 18/8 steel stabilised by Titanium or additions. These grades are used because they are not sensitive to intergranular corrosion after heating within the carbide precipitation range of 425-850°C.GB H0Cr20Ni10Ti is the grade of choice for applications in the temperature range of up to about 900°C, combining high strength, resistance to scaling and phase stability with resistance to subsequent aqueous corrosion. Cold Bending : It has excellent cold working properties and cold bending can generally be carried out without too much difficulty. Hot Bending : Hot bending should be performed at 950oC - 1100Oc. Corrosion Resistance : it similar resistance to general corrosion in most media as 304, but not as good as 316. Stress Corrosion Cracking : it has similar resistance to stress corrosion cracking as 304, but not as good as 316. Pitting Corrosion / Crevice Corrosion : It has similar resistance to pitting and crevice corrosion as 304, but not as good as 316. Intergranular Corrosion : it has better resistance to intergranular corrosion than most of the standard 300 grades other than the low carbon types 304L, 316L and 317L due to its titanium content.N.B. Forging : Heat uniformly to 1150oC - 1200oC Machining: It is more difficult to machine than most of the standard austenitic stainless steels, due to its titanium addition. Our Domestic reach is unlimited and we supply to this following cities Ahmedabad, Amritsar, Aurangabad, Bangalore, Bhopal, Chandigarh, Chennai, Coimbatore, Dhanbad, Faridabad, Ghaziabad, Guwahati, Gwalior, Howrah, Hyderabad, Indore, Jabalpur, Jaipur, Jodhpur, Kanpur, Kolkata, Kota, Lucknow, Ludhiana, Madurai, Meerut, Mumbai, Nagpur, Nashik, Navi Mumbai, New Delhi, Patna, Pune, Raipur, Rajkot, Ranchi, Solapur, Srinagar, Surat, Thane, Vadodara, Varanasi, Vijayawada, Visakhapatnam, Hubballi, Tiruchirappalli, Bareilly, Moradabad, Mysore, Gurgaon, Aligarh, Jalandhar, Bhubaneswar We export to following Countries: Russia, Canada, United States, China, Brazil, Australia, Argentina, Kazakhstan, Algeria, Denmark, Saudi Arabia, Mexico, Indonesia, Iran, Mongolia, Peru, South Africa, Colombia, Ethiopia, Bolivia, Egypt, Venezuela, Turkey, Chile, Myanmar, France, Ukraine, Madagascar, Botswana, Kenya, Thailand, Spain, Sweden, Uzbekistan, Morocco, Paraguay, Zimbabwe, Norway, Japan, Germany, Republic of the Congo, Finland, Vietnam, Malaysia, Poland, Oman, Italy, Philippines, Ecuador, New Zealand, United Kingdom, Guinea, Uganda, Nepal, Bangladesh