'higher risks'

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are designed to protect boiler tubes, heat exchanger coils, and superheaters from erosion, scaling, slag accumulation, and corrosive flue gases. These shields are widely used in thermal systems such as power plants, chemical processing units, and waste heat recovery boilers to improve tube longevity and reduce maintenance frequency. Their semi-cylindrical form allows easy installation on straight or curved tube surfaces in high-wear zones. SS 316 Half Round Tube Shield for LTSH Tube The SS 316 Half Round Tube Shield is manufactured from molybdenum-bearing austenitic stainless steel grade 316. Known for its excellent resistance to pitting, crevice corrosion, and chemical attack, SS 316 is ideal for environments where flue gas contains chlorides, moisture, or mildly acidic compounds. Designed specifically for Low Temperature Superheater (LTSH) applications, this shield provides critical surface protection in zones where steam is moderately superheated and tubes are exposed to ash, soot, and thermal cycling. The Low Temperature Superheater (LTSH) is a section in a boiler where saturated steam from the steam drum is superheated to a moderately higher temperature before entering the high-temperature superheater stages. Positioned in areas with relatively lower flue gas temperatures, the LTSH helps improve thermal efficiency and reduces moisture content in steam. Due to constant exposure to abrasive flue gases and ash, LTSH tubes are prone to wear and require protective shielding, such as half round tube shields, to extend service life. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of SS 316 Half Round Tube Shields for LTSH applications, offering reliable and corrosion-resistant shielding solutions for extended tube performance. Chemical Composition of SS 316 – Austenitic Stainless Steel with Molybdenum • Carbon (C): ≤ 0.08% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Nickel (Ni): 10.0 – 14.0% • Molybdenum (Mo): 2.0 – 3.0% • Iron (Fe): Balance Applications: Suitable for low-temperature superheater zones exposed to corrosive ash, flue gas condensation, and thermal cycling, especially in coastal or chloride-rich environments. Uses • Installed on LTSH tubes in utility boilers to protect against acidic flue gas corrosion and soot erosion • Shields exposed tube sections in convection zones, economizers, and HRSG units • Applied in boilers using high-sulfur coal or biomass, where corrosion risks are elevated • Suitable for industrial steam systems and chemical processing units handling corrosive exhaust • Used in power plants operating in marine or high-humidity conditions Features • Superior corrosion resistance – Withstands chloride attack, acidic deposits, and moisture exposure • Thermal durability – Maintains mechanical strength and oxidation resistance under moderate heat • Custom fabrication – Manufactured to match the diameter and length of LTSH tubes for accurate fit • Easy to install – Compatible with welding, banding, or clamping methods • Reduces wear – Protects against pitting, scale buildup, and erosion in flue gas flow paths • Available in multiple thicknesses, lengths, and radii based on system design Applications • thermal power plants – Shields LTSH tubes to improve service life and efficiency • chemical plants – Applied in low-temperature zones of process boilers exposed to aggressive gases • waste heat recovery – Protects return coil sections from corrosion and erosion in WHRBs and HRSGs • industrial boilers – Guards tube surfaces in preheaters and economizers under corrosive flue conditions • steam generation systems – Used in moisture-laden or coastal plant environments requiring enhanced protection Conclusion The SS 316 Half Round Tube Shield for LTSH Tube by Ladhani Metal Corporation – manufacturer, supplier, and exporter – delivers high-performance protection for boiler and superheater tubes in corrosive, low-temperature environments. With its excellent corrosion resistance and reliable thermal performance, it ensures extended operational life and reduced maintenance in critical heat exchange systems. For technical support, customization, or pricing inquiries, please contact Ladhani Metal Corporation.

Product Name: Titanium racks for aluminum anodizing Material: Gr1, Gr2 Application: Electroplating, anodizing etc. Size: Customized Surface: Polished Type : Titanium racks / Titanium Jigs Dimenstion and shape : Customized, as customer's drawings Finishing : Polished Material : Pure Titanium(gr1 gr2) Condition : New Application : Electroplating, anodizing etc Color : Sliver.Grey Features : Anti-corrosion, good elasticity, smooth surface, dustproof, strong structure, good quality, fine surface We provide various titanium plating rack jigs. These ranges of jigs are available in different sizes to maximize customer satisfaction. Also, these jigs are provided at very affordable prices. Our technique can adapt jigs to the most suitable parts and materials, so that the product has higher durability and strength. Our production system reduces the entrainment of impurities and liquids between tanks and improves the passage of current, as well as its uniform distribution throughout the whole rack. The continuous availability of raw materials, laser cutting machines, folding and automatic welding machines makes our products the most competitive in the market and able to complete tasks within very tight deadlines. Chemical composition (Wt%) ASTM No. Fe max O max N max C max H max Pd Al Bal Grade 1 0.2 0.18 0.03 0.1 0.015 - - Ti Grade 2 0.3 0.25 0.03 0.1 0.015 - - Ti Physical Properties (Min) ASTM Grade Alloy Composition Tensile Strength Yield Strength Elongation min % ksi Mpa ksi Mpa Grade 1 Unalloyed Ti ("Pure") 35A -CP1 35 240 25 170 30 Grade 2 Unalloyed Ti ("Pure") 50A -CP2 58 400 40 275 25

Ladhani Metal Corporation offers U-Bend Half-Round Tube Shields, specially designed to protect U-bend sections of boiler tubes in power plants, waste heat recovery boilers (WHRBs), heat recovery steam generators (HRSGs), and industrial steam systems. U-bend areas are highly susceptible to erosion, flue gas impingement, and abrasive wear caused by high-velocity gases and ash particles. These shields provide durable protection, reducing tube thinning, failure risks, and extending the operational lifespan of the boiler tubes. Function of U-Bend Sections • Carry water or steam through tight-radius bends in boiler heating circuits • Exposed to flue gas turbulence, high temperatures, and particle erosion • Protected with Half-Round Shields to minimize erosion and wear at bends Ladhani Metal Corporation manufactures, supplies, and exports U-Bend Half-Round Tube Shields in customized lengths, radii, and thicknesses, ensuring precision fitment for various boiler tube configurations. Available Grades • SS 304 / SS 304L • SS 310 / SS 310S • SS 316 / SS 316L • SS 410 / SS 420 / SS 430 • Cr25Ni20 / Cr23Ni13 • 1Cr13 / 1Cr18Ni9Ti / 1Cr20Ni14Si2 / 1Cr25Ni20Si2 Applications: Suitable for U-bend sections in boilers operating under high thermal stress, oxidation-prone environments, and abrasive gas flows. Widely used in utility boilers, WHRBs, HRSGs, and industrial steam generators. Uses • Shields U-bend tube areas from flue gas erosion and soot blower impact • Reduces tube wall thinning and premature failures in bends • Ensures reliability of boiler heating circuits under harsh conditions • Extends service life of reheater, superheater, and economizer sections Features • Excellent resistance to erosion and oxidation • Available in multiple stainless steel grades and heat-resistant alloys • High thermal stability in elevated-temperature environments • Precision-engineered to match U-bend geometry for easy installation Applications • Power plant boilers – Protection of U-bends in reheater and superheater tubes • Waste heat recovery boilers – Guards tight-radius bends against particle erosion • HRSGs – Extends service life of critical tube sections • Petrochemical and industrial steam boilers – Reliable in fluctuating thermal cycles Conclusion The U-Bend Half-Round Tube Shield by Ladhani Metal Corporation is a reliable solution for safeguarding boiler tube bends against erosion, oxidation, and thermal stress. Available in a wide range of stainless steels and heat-resistant alloys, these shields are manufactured with precision to meet domestic and international standards. For technical support and supply inquiries, contact Ladhani Metal Corporation.

Ladhani Metal Corporation offers SS 310S Half Round Tube Shields designed to safeguard boiler tubes operating under high-temperature and erosive conditions in power plants, HRSGs, WHRBs, and industrial steam systems. Boiler tubes are constantly exposed to oxidation, flue gas erosion, and soot blower impact, leading to premature wear and reduced efficiency. Manufactured from low-carbon austenitic stainless steel grade SS 310S, these shields provide exceptional oxidation resistance, superior creep strength, and reduced risk of sensitization during welding, making them ideal for prolonged high-temperature service. Function of Boiler Tubes • Carry water or steam through heating sections of the boiler • Exposed to erosion from high-velocity flue gases and ash particles • Require Half Round Tube Shields in soot blower zones and high-temperature erosion areas Ladhani Metal Corporation manufactures, supplies, and exports SS 310S Half Round Tube Shields in multiple lengths, diameters, and thicknesses to meet the requirements of both domestic and international clients. SS 310S Grade Chemical Composition – Austenitic Stainless Steel • Carbon (C): ≤ 0.08% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.50% • Chromium (Cr): 24.00 – 26.00% • Nickel (Ni): 19.00 – 22.00% • Iron (Fe): Balance Applications: Well-suited for use in reheater and superheater sections of thermal power plants, waste heat recovery boilers, HRSGs, and industrial boilers operating under extreme thermal and corrosive environments. Uses • Protects boiler tubes against oxidation and flue gas erosion • Shields tubes from soot blower erosion and abrasive particle damage • Extends operational life of superheater and reheater tubes • Used extensively in HRSGs, WHRBs, and large-scale utility boilers Features • Excellent oxidation resistance up to 1100°C • Low carbon content reduces sensitization risk during welding • Superior strength and stability in prolonged high-temperature service • Engineered for precise fit and easy installation Applications • Power generation boilers – Reheater and superheater tube protection in high-erosion zones • Waste heat recovery boilers – Guards tubes from ash-laden flue gas streams • Industrial steam systems – Reliable under continuous high-temperature operation • Petrochemical and refinery heaters – Suitable for oxidizing and carburizing service conditions Conclusion The SS 310S Half Round Tube Shield for Boiler Tubes by Ladhani Metal Corporation provides long-lasting protection under severe high-temperature and erosive conditions. With its low-carbon content and high oxidation resistance, it minimizes sensitization risks while extending the life of boiler tubes. Available in export-ready specifications, these shields are the preferred choice for industries worldwide seeking durability, efficiency, and cost-effectiveness. For detailed technical information and supply inquiries, contact Ladhani Metal Corporation. #Mumbai #Pune #Ahmedabad #Vadodara #Surat #Rajkot #Jamnagar #Bharuch #Ankleshwar #Vapi #Delhi #Faridabad #Ghaziabad #Noida #Gurugram #Chennai #Coimbatore #Tiruchirappalli #Hyderabad #Visakhapatnam #Vijayawada #Bangalore #Mangalore #Mysore #Kolkata #Durgapur #Asansol #Bhubaneswar #Rourkela #Raipur #Bhilai #Bilaspur #Nagpur #Nashik #Aurangabad #Indore #Bhopal #Jabalpur #Kanpur #Lucknow #Varanasi #Jaipur #Kota #Udaipur #Jodhpur #Chandigarh #Ludhiana #Jalandhar #Haridwar #Dehradun #Agra #Meerut #Aligarh #Moradabad #Bareilly #Mathura #Gwalior #Rewa #Satna #Sagar #Ujjain #Ratlam #Solapur #Kolhapur #Amravati #Akola #Jalgaon #Latur #Sangli #Nanded #Gandhinagar #Bhavnagar #Mehsana #Surendranagar #Junagadh #Nadiad #Nizamabad #Karimnagar #Warangal #Kurnool #Nellore #Tirupati #Madurai #Tirunelveli #Thoothukudi #Belgaum #Hubli #Tumkur #Sambalpur #Jamshedpur #Ranchi #Dhanbad #Patna #Muzaffarpur#halftubeshield #utypehalftubeshield #tubeshieldexporter #TubeShield #HalfTubeShield #SSHalfRoundShield #BoilerTubeShield #BoilerShield #TubeProtection #Tubeshieldmanufacturer #BoilerTubeProtection #SSTubeShield #MetalIndustry #SteelFabrication #IndustrialShielding #SS304Shield #SS316Shield #StainlessSteelShield #WeldOnShield #WeldedTubeShield #TubeCladding #BoilerTubeSleeve #TubeSleeve #MetalFabrication #PowerPlantSupplies #RefineryEquipment #ProcessIndustry #MetalComponent #TubeShieldForBoilers #BoilerParts #SteelSolutions #TubeShieldManufacturer #TubeShieldSupplier #SSShielding #IndustrialTubeShield #BoilerTubeGuard #CustomMetalParts #SteelIndustryIndia #MetalEngineering #HeavyIndustrySupply #StainlessSteelIndia #SteelExporters #MetalComponentExport #FabricatedProducts #SteelDealer #IndustrialSupplyIndia #BoilerTubeFittings #TubeShieldingSolutions #HalfTubeCover #HeatExchangerShield #HalfRoundReheaterShield #ReheaterTubeShield #BoilerReheaterProtection #PowerPlantTubeShield #BoilerErosionShield #SteamBoilerTubeShield #HighTempTubeShield #BoilerWearProtection

QUALITY STANDARD MATERIAL NO. OLD DESIGNATION DC04 DIN EN 10130 1.0338 St 14-03 The special deep-drawing grade DC04 is specified in accordance with the standard DIN EN 10130, which focuses on cold-rolled flat products made of soft steels for cold forming. This standard specifies the technical requirements and test methods for cold-rolled products that are important in numerous industrial applications, especially where high formability and excellent surface quality are required. DC04 is a low-carbon steel that impresses with its exceptional cold formability. The chemical composition of DC04 is precisely balanced to ensure that the material has the desired mechanical properties. The carbon content in DC04 is typically a maximum of 0.08 %, while the manganese content is a maximum of 0.40 %. This composition supports the high formability and weldability of the steel, making it ideal for demanding forming processes. The mechanical properties of DC04 are characterized by a low yield strength of maximum 210 MPa and a tensile strength between 270 and 350 MPa. Particularly noteworthy is the high elongation at break of at least 38%, which illustrates the excellent formability of the material. These properties make DC04 a preferred choice for the production of complex components that require high precision and surface quality, such as car body components in the automotive industry or filigree parts in the electronics industry. The DIN EN 10130 standard also specifies the tolerances for dimensions, shape and surface finish. These tolerances are crucial to ensure consistently high product quality and to meet the requirements of end users. The surface of the cold-rolled flat products can be supplied in various qualities, from matt to high-gloss, to meet the specific requirements of different applications. The DIN EN 10152 standard specifies electrolytically galvanized, cold-rolled flat steel products for cold forming, including the special deep-drawing grade DC04. This standard defines the requirements for the zinc coating and the basic mechanical properties of the base material. DC04, when electrolytically galvanized in accordance with DIN EN 10152, is given an additional corrosion protection layer of zinc. This layer protects the material from oxidative influences and significantly increases the service life of the components made from it. The zinc coating can be applied in various thicknesses, depending on the specific requirements of the application. Typical coating thicknesses range from 5 to 20 µm. The chemical composition and mechanical properties of the base material DC04 remain unchanged even after galvanizing and meet the requirements of DIN EN 10130. DC04 therefore retains its excellent cold formability and mechanical performance. In addition to mechanical performance, the quality of the zinc coating is of central importance. The DIN EN 10152 standard specifies the requirements for the uniformity of the coating, the adhesive strength of the zinc and the surface quality. These requirements ensure that the galvanized products offer high corrosion resistance and an aesthetically pleasing surface. The use of DC04 in accordance with DIN EN 10152 is widespread in the automotive industry, the construction industry and in the manufacture of household appliances, where improved corrosion resistance is required in addition to high formability. Electrolytic galvanizing offers optimum protection here without impairing the excellent mechanical properties of the base material. DC04 and DC01 are both cold-rolled, unalloyed quality steels that are used for various industrial applications. While DC01 serves as the standard grade for general cold forming processes, DC04 is characterized by improved deep-drawing properties and higher ductility. This comparison highlights the differences between the two materials in terms of chemical composition, mechanical properties and typical applications. Chemical composition The chemical composition influences the formability and weldability of the steel. Both steels are made of carbon steel, but DC04 has a lower carbon content, which supports its improved cold formability. Thanks to the lower carbon and Sulphur content, DC04 offers improved deep-drawing capability as less intergranular embrittlement occurs. Mechanical properties The mechanical properties are decisive for the forming processes and the behavior of the steel under load. DC04 has a lower yield strength and higher elongation, which makes the material easier to form. The lower yield strength and increased minimum elongation of DC04 make this material ideal for demanding forming processes such as deep drawing.

QUALITY STANDARD MATERIAL NO. OLD DESIGNATION DC04 DIN EN 10130 1.0338 St 14-03 The special deep-drawing grade DC04 is specified in accordance with the standard DIN EN 10130, which focuses on cold-rolled flat products made of soft steels for cold forming. This standard specifies the technical requirements and test methods for cold-rolled products that are important in numerous industrial applications, especially where high formability and excellent surface quality are required. DC04 is a low-carbon steel that impresses with its exceptional cold formability. The chemical composition of DC04 is precisely balanced to ensure that the material has the desired mechanical properties. The carbon content in DC04 is typically a maximum of 0.08 %, while the manganese content is a maximum of 0.40 %. This composition supports the high formability and weldability of the steel, making it ideal for demanding forming processes. The mechanical properties of DC04 are characterized by a low yield strength of maximum 210 MPa and a tensile strength between 270 and 350 MPa. Particularly noteworthy is the high elongation at break of at least 38%, which illustrates the excellent formability of the material. These properties make DC04 a preferred choice for the production of complex components that require high precision and surface quality, such as car body components in the automotive industry or filigree parts in the electronics industry. The DIN EN 10130 standard also specifies the tolerances for dimensions, shape and surface finish. These tolerances are crucial to ensure consistently high product quality and to meet the requirements of end users. The surface of the cold-rolled flat products can be supplied in various qualities, from matt to high-gloss, to meet the specific requirements of different applications. The DIN EN 10152 standard specifies electrolytically galvanized, cold-rolled flat steel products for cold forming, including the special deep-drawing grade DC04. This standard defines the requirements for the zinc coating and the basic mechanical properties of the base material. DC04, when electrolytically galvanized in accordance with DIN EN 10152, is given an additional corrosion protection layer of zinc. This layer protects the material from oxidative influences and significantly increases the service life of the components made from it. The zinc coating can be applied in various thicknesses, depending on the specific requirements of the application. Typical coating thicknesses range from 5 to 20 µm. The chemical composition and mechanical properties of the base material DC04 remain unchanged even after galvanizing and meet the requirements of DIN EN 10130. DC04 therefore retains its excellent cold formability and mechanical performance. In addition to mechanical performance, the quality of the zinc coating is of central importance. The DIN EN 10152 standard specifies the requirements for the uniformity of the coating, the adhesive strength of the zinc and the surface quality. These requirements ensure that the galvanized products offer high corrosion resistance and an aesthetically pleasing surface. The use of DC04 in accordance with DIN EN 10152 is widespread in the automotive industry, the construction industry and in the manufacture of household appliances, where improved corrosion resistance is required in addition to high formability. Electrolytic galvanizing offers optimum protection here without impairing the excellent mechanical properties of the base material. DC04 and DC01 are both cold-rolled, unalloyed quality steels that are used for various industrial applications. While DC01 serves as the standard grade for general cold forming processes, DC04 is characterized by improved deep-drawing properties and higher ductility. This comparison highlights the differences between the two materials in terms of chemical composition, mechanical properties and typical applications. Chemical composition The chemical composition influences the formability and weldability of the steel. Both steels are made of carbon steel, but DC04 has a lower carbon content, which supports its improved cold formability. Thanks to the lower carbon and Sulphur content, DC04 offers improved deep-drawing capability as less intergranular embrittlement occurs. Mechanical properties The mechanical properties are decisive for the forming processes and the behavior of the steel under load. DC04 has a lower yield strength and higher elongation, which makes the material easier to form. The lower yield strength and increased minimum elongation of DC04 make this material ideal for demanding forming processes such as deep drawing.

Product Name: Titanium Pipe Standard: ASTM B861, ASTM B862 Material: Gr7 Type: Welded/Seamless Shape: Round Outer Diameter: 3-114mm or as customized Wall Thickness: 0.5-7mm or as customized Length: Max 12000mm Surface: Bright Product Information of Grade 7 Titanium Pipe Material: Gr7 Standard: ASTM B861, ASTM B862 OD: 3-114mm or as customized WT: 0.5-7mm or as customized Length: Max 12m Type: Welded/Seamless Surface: Polishing, Pickling Grade 7 Titanium Grade 7 titanium has physical and mechanical properties equivalent to Grade 2 titanium (CP3). It has excellent welding and fabrication properties and is extremely resistant to corrosion, especially from reducing acids.

Product Name: Titanium rod grade 23 Standard: ASTM F136 Material: Gr23 (Gr5 ELI) Unit Price: $30.5 usd/kg- $52.5 usd/kg Application: Medical use Shape: Round Diameter: 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm, 16mm, 20mm etc. Length: 1000mm, 3000mm, 6000mm or as per your request Surface: Bright Product Introduction Product name:Titanium rod grade 23 Material: GR23 Standard: ASTM F136 Diameter: 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm, 16mm, 20mm etc. Length: 1000mm, 3000mm, 6000mm or as per your request Surface: Polishing,Bright Third-Party Tests: BV, SGS, TUV etc. Grade 23 is a higher purity version of Ti 6Al-4V. It can be made into coils, strands, wires or flat wires and is the first choice for any occasion that requires a combination of high strength, light weight, good corrosion resistance and high toughness. It has excellenct damage resistance superior to other alloys. These advantages make Ti 6AL-4V ELI the final dental and medical titanium grade product. Due to its biocompatibility, good fatigue strength and lo mdulus, it can be used in biomedical applications such as implantable parts. Grade 23 can also be used in detailed surgical procedures, such as: • Orthopedic pins and screws • Orthopedic cables • Ligation needles • Surgical staples • Springs • Orthodontic appliances • Joint replacements • Cryogenic containers • Bone fixators Mechanical Properties: Grade Tensile strength, MPa (min) Yield strength, MPa (min) Elongation, %(min) Reduction of Area, %(min) Gr23 828 759 10 15 Chemical Component (ASTM B348) Grade Ti Al V N, max C, max H, max Fe, max O, max Residuals Max each Max total Gr23 Main 5.5-6.5 3.5-4.5 0.03 0.08 0.0125 0.25 0.13 0.1 0.4

Product Name: Grade 2 titanium welding wire Standard: AWS A5.16 Material: Grade 2 (ERTi-2) Unit Price: $21.5usd/kg-$60usd/kg Shape: Straight, Spool, Coil Diameter: 0.8mm/1mm/1.2mm/1.6mm/2mm/2.4mm/3mm/3.2mm etc. Grade 2 titanium welding wire Standard: AWS A5.16 Material: Grade 2 (ERTi-2) Unit Price: $21.5usd/kg-$60usd/kg Shape: Straight, Spool, Coil Diameter: 0.8mm/1mm/1.2mm/1.6mm/2mm/2.4mm/3mm/3.2mm etc. Surface: Bright Chemical composition (Wt%) ASTM No. Fe max O max N max C max H max Pd Al Bal Grade 2 0.3 0.25 0.03 0.1 0.015 - - Ti Physical Properties (Min) ASTM Grade Alloy Composition Tensile Strength Yield Strength Elongation min % ksi Mpa ksi Mpa Grade 2 Unalloyed Ti ("Pure") 50A -CP2 58 400 40 275 25 Features of our company's titanium welding wire: 　　1. Manufactured by a non-oxidized roll mold cold drawing process 　　2, the welding wire has uniform structure and fine grains 　　3, high dimensional accuracy, no defects, excellent follow-up processing performance 　　4, the composition of various elements in the material and the mechanical properties of the material can be effectively controlled