'oxidation slag deposits'

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are designed to protect boiler tubes, heat exchanger coils, and superheaters from erosion, scaling, slag accumulation, and corrosive flue gases. These shields are widely used in thermal systems such as power plants, chemical processing units, and waste heat recovery boilers to improve tube longevity and reduce maintenance frequency. Their semi-cylindrical form allows easy installation on straight or curved tube surfaces in high-wear zones. SS 316 Half Round Tube Shield for LTSH Tube The SS 316 Half Round Tube Shield is manufactured from molybdenum-bearing austenitic stainless steel grade 316. Known for its excellent resistance to pitting, crevice corrosion, and chemical attack, SS 316 is ideal for environments where flue gas contains chlorides, moisture, or mildly acidic compounds. Designed specifically for Low Temperature Superheater (LTSH) applications, this shield provides critical surface protection in zones where steam is moderately superheated and tubes are exposed to ash, soot, and thermal cycling. The Low Temperature Superheater (LTSH) is a section in a boiler where saturated steam from the steam drum is superheated to a moderately higher temperature before entering the high-temperature superheater stages. Positioned in areas with relatively lower flue gas temperatures, the LTSH helps improve thermal efficiency and reduces moisture content in steam. Due to constant exposure to abrasive flue gases and ash, LTSH tubes are prone to wear and require protective shielding, such as half round tube shields, to extend service life. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of SS 316 Half Round Tube Shields for LTSH applications, offering reliable and corrosion-resistant shielding solutions for extended tube performance. Chemical Composition of SS 316 – Austenitic Stainless Steel with Molybdenum • Carbon (C): ≤ 0.08% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Nickel (Ni): 10.0 – 14.0% • Molybdenum (Mo): 2.0 – 3.0% • Iron (Fe): Balance Applications: Suitable for low-temperature superheater zones exposed to corrosive ash, flue gas condensation, and thermal cycling, especially in coastal or chloride-rich environments. Uses • Installed on LTSH tubes in utility boilers to protect against acidic flue gas corrosion and soot erosion • Shields exposed tube sections in convection zones, economizers, and HRSG units • Applied in boilers using high-sulfur coal or biomass, where corrosion risks are elevated • Suitable for industrial steam systems and chemical processing units handling corrosive exhaust • Used in power plants operating in marine or high-humidity conditions Features • Superior corrosion resistance – Withstands chloride attack, acidic deposits, and moisture exposure • Thermal durability – Maintains mechanical strength and oxidation resistance under moderate heat • Custom fabrication – Manufactured to match the diameter and length of LTSH tubes for accurate fit • Easy to install – Compatible with welding, banding, or clamping methods • Reduces wear – Protects against pitting, scale buildup, and erosion in flue gas flow paths • Available in multiple thicknesses, lengths, and radii based on system design Applications • thermal power plants – Shields LTSH tubes to improve service life and efficiency • chemical plants – Applied in low-temperature zones of process boilers exposed to aggressive gases • waste heat recovery – Protects return coil sections from corrosion and erosion in WHRBs and HRSGs • industrial boilers – Guards tube surfaces in preheaters and economizers under corrosive flue conditions • steam generation systems – Used in moisture-laden or coastal plant environments requiring enhanced protection Conclusion The SS 316 Half Round Tube Shield for LTSH Tube by Ladhani Metal Corporation – manufacturer, supplier, and exporter – delivers high-performance protection for boiler and superheater tubes in corrosive, low-temperature environments. With its excellent corrosion resistance and reliable thermal performance, it ensures extended operational life and reduced maintenance in critical heat exchange systems. For technical support, customization, or pricing inquiries, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are protective components designed to guard heat exchanger coils, boiler tubes, and superheater assemblies from erosion, high-temperature scaling, slag accumulation, and corrosion. These shields are vital in high-performance industrial systems, including power plants, refineries, and chemical process units. Their half-round shape allows easy installation on both straight and curved tubes, improving system longevity while minimizing downtime and maintenance frequency. 1Cr20Ni14Si2 U Type Inner Half Round Tube Shield The 1Cr20Ni14Si2 U Type Inner Half Round Tube Shield is manufactured using a high-temperature austenitic stainless steel alloy with enhanced chromium, nickel, and silicon content. This alloy delivers excellent oxidation resistance, thermal fatigue resistance, and structural stability at elevated temperatures. The inner U-type configuration is tailored to cover the inner arc of U-bend tubes, offering critical protection where high-velocity gas, turbulence, and slag deposits can rapidly wear or degrade tube surfaces. • Inner U Type Half Round Tube Shield – Designed to protect the inner curvature of U-bend tubes from scaling, erosion, and heat-related damage in thermal systems. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of 1Cr20Ni14Si2 U Type Inner Half Round Tube Shields, delivering high-performance shielding solutions for demanding high-temperature environments. Chemical Composition of 1Cr20Ni14Si2 – High Chromium-Nickel-Silicon Heat-Resistant Alloy • Carbon (C): ≤ 0.20% • Manganese (Mn): ≤ 1.50% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): 1.80 – 2.50% • Chromium (Cr): 19.0 – 21.0% • Nickel (Ni): 13.0 – 15.0% • Iron (Fe): Balance Applications: Ideal for continuous high-temperature operations involving oxidizing or sulfur-containing gases. Well-suited for applications requiring excellent heat resistance and minimal thermal deformation. Uses • Shields inner arcs of U-bend tubes in boilers and superheaters operating at elevated temperatures • Installed in WHRBs and HRSGs to prevent scaling, slag, and erosion in internal tube bends • Used in curved coils in reformers and process heaters exposed to hot gas and thermal cycling • Protects tube bends in chemical reactors, incinerators, and industrial furnaces from oxidation and surface degradation • Effective in systems where stability at high temperatures and resistance to carburizing and sulfidizing environments are essential Features • Excellent high-temperature performance – Withstands long-term exposure to temperatures exceeding 1000°C • Inner arc coverage – Precisely shields erosion-prone internal tube bends in critical heat transfer zones • Superior oxidation and scaling resistance – Resists corrosion in aggressive combustion gas atmospheres • Custom-fit design – Fabricated according to specified tube radii and diameters for optimal coverage and secure fit • Quick and secure installation – Compatible with clamping, banding, or tack welding methods • Long operational life – Reduces the frequency of tube failures, improving reliability and plant efficiency Applications • power plants – Installed on U-bend tubes in superheaters and reheaters facing continuous high-temperature service • petrochemical plants – Protects inner arcs of tubes in reformers and gas processing heat exchangers • waste heat recovery – Shields return bends in WHRBs and HRSGs exposed to hot flue gas and slag • thermal processing – Applied in furnaces and incinerators where hot combustion gases affect internal tube surfaces • chemical industry – Guards against oxidizing and corrosive gas damage in curved tube sections of reactors Conclusion The 1Cr20Ni14Si2 U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a robust and heat-resistant solution for protecting U-bend tubes in high-temperature and chemically aggressive conditions. Its high alloy composition, excellent thermal resistance, and customized fitment make it ideal for enhancing tube performance and reliability in critical thermal systems. For technical specifications, customized fabrication, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-engineered components used to protect boiler and heat exchanger tubes from erosion, scaling, and high-temperature corrosion. These shields are widely applied in industrial systems exposed to thermal cycling, aggressive gases, and particulate flow. Their half-round shape allows for simple and secure installation over straight or curved tube surfaces, extending tube life and reducing maintenance needs. SS 410 U Type Outer Half Round Tube Shield The SS 410 U Type Outer Half Round Tube Shield is made from SS 410, a hardenable martensitic stainless steel known for its excellent strength, toughness, and moderate corrosion resistance. This outer U-type configuration is designed to protect the external arc of U-bend tubes in heat exchangers, boilers, and reheaters where abrasive flue gases and mechanical wear are common. SS 410’s hardness and resistance to thermal fatigue make it suitable for shielding outer tube surfaces exposed to harsh industrial environments. • Outer U Type Half Round Tube Shield – Protects the outer curvature of U-bend tubes from erosion, scaling, and mechanical impact caused by high-velocity gas and slag deposits. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of SS 410 U Type Outer Half Round Tube Shields, offering durable solutions for power generation and high-temperature applications. Chemical Composition of SS 410 – Martensitic Stainless Steel • Carbon (C): 0.08 – 0.15% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 11.5 – 13.5% • Nickel (Ni): ≤ 0.75% • Iron (Fe): Balance Applications: Suitable for high-temperature environments with abrasive gas flow and mechanical stress, where moderate corrosion resistance is sufficient. Uses • Outer arc protection for U-bend tubes in boilers, superheaters, and reheaters in thermal power plants • Shields tube bends in economizers and waste heat recovery systems from flue gas erosion • Applied in return bends in gas processing heaters and exhaust systems subjected to particulate flow • Ideal for high-strength, mechanically demanding environments where wear resistance is critical • Used in utility boilers, process furnaces, and other industrial systems operating under moderate corrosion and high heat conditions Features • High mechanical strength – Martensitic structure provides excellent hardness and wear resistance for abrasive service conditions • Moderate corrosion resistance – Chromium content offers basic protection against oxidation and steam exposure • Outer bend coverage – Shields the most exposed and impact-prone arc of the U-bend tube • Precision fit – Custom-fabricated to match tube diameters and bend radii, ensuring tight, vibration-free installation • Easy to install – Mountable using stainless steel bands, clamps, or tack welds without dismantling the system • Cost-effective – Offers durable tube protection with high strength at a lower material cost compared to austenitic grades Applications • power generation – Protects outer curves of U-bend tubes in high-temperature zones of boilers and reheaters • petrochemical processing – Shields tube bends in process heaters and reformers from thermal and gas erosion • waste heat recovery – Applied in WHRBs and HRSGs to guard against slag impact and scale formation • industrial furnaces – Suitable for high-wear zones where heat and particulate flow cause surface degradation • general industry – Used in utility boilers and gas exhaust systems where mechanical protection is needed with moderate corrosion resistance Conclusion The SS 410 U Type Outer Half Round Tube Shield by Ladhani Metal Corporation—manufacturer, supplier, and exporter—is a reliable and economical solution for protecting U-bend tube outer surfaces in boilers, heat exchangers, and thermal process systems. With excellent mechanical strength, good thermal stability, and moderate corrosion resistance, it is ideal for industrial applications that demand abrasion resistance and long service life in high-temperature environments. For technical consultation, custom orders, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-engineered components used to protect boiler and heat exchanger tubes from erosion, scaling, and high-temperature corrosion. These shields are widely applied in industrial systems exposed to thermal cycling, aggressive gases, and particulate flow. Their half-round shape allows for simple and secure installation over straight or curved tube surfaces, extending tube life and reducing maintenance needs. 1Cr20Ni14Si2 U Type Half Round Tube Shield The 1Cr20Ni14Si2 U Type Half Round Tube Shield is manufactured from a high-temperature austenitic stainless steel alloy designed for demanding thermal environments. Composed primarily of chromium and nickel with enhanced silicon content, this alloy provides outstanding resistance to oxidation, scaling, carburization, and thermal fatigue. It is particularly effective in shielding U-bend tube sections within boilers, reformers, and heat recovery systems where prolonged exposure to high heat and reactive gases can degrade performance. The U-type configuration ensures full coverage of the inner and outer arcs of curved tubes, delivering comprehensive protection against mechanical and thermal damage. • Outer U Type Half Round Tube Shield – Protects the outer curvature of U-bends from high-temperature flue gas erosion, slag deposits, and oxidizing environments. • Inner U Type Half Round Tube Shield – Shields the inner bend arc from thermal stress cracking, scale formation, and turbulence-induced wear. Ladhani Metal Corporation provides 1Cr20Ni14Si2 U Type Half Round Tube Shields for industries requiring reliable, long-term protection in aggressive high-temperature service conditions. Chemical Composition of 1Cr20Ni14Si2 – Heat-Resistant Austenitic Stainless Steel • Carbon (C): ≤ 0.15% • Manganese (Mn): ≤ 1.50% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): 1.50 – 2.50% • Chromium (Cr): 19.0 – 21.0% • Nickel (Ni): 13.0 – 15.0% • Iron (Fe): Balance Applications: Ideal for continuous and cyclic high-temperature systems where resistance to oxidation, thermal fatigue, and carburization is critical. Uses • Protection of U-bend tubes in superheaters and reheaters in power generation systems • Shielding of return bends in waste heat recovery boilers and HRSGs operating under high flue gas flow • Coverage for curved tube sections in reformers, cracking furnaces, and thermal oxidizers • Safeguarding tube bends in heat exchangers, condensers, and process gas heating systems • Applicable in chemical, metallurgical, and energy industries where extreme thermal cycling and gas exposure occur Features • Excellent oxidation resistance – Chromium and silicon-rich composition provides strong protection against scaling in high-temperature, oxidizing atmospheres. • Superior thermal fatigue performance – Maintains mechanical strength and dimensional stability under rapid temperature fluctuations. • Dual-arc shielding – Available in inner and outer U-type configurations for total protection of return bends in heat exchanger systems. • Precision engineered – Manufactured to match tube diameter and bend radius, ensuring tight, secure installation without vibration or misalignment. • Easy to install – Can be quickly mounted using banding, clamps, or tack welds without the need to disassemble tube bundles. • Long service life – Designed for demanding environments, reducing maintenance frequency and enhancing overall system efficiency. Applications • thermal power plants – Installed in U-bends of superheaters and reheaters to prevent heat-induced scaling, erosion, and fatigue cracking. Improves reliability and heat transfer efficiency. • petrochemical and refinery units – Used in process heaters, reformers, and thermal units where high-temperature gas exposure is constant. Provides stable, long-term protection. • waste heat recovery units – Shields U-shaped tubes in WHRBs and HRSGs from slag deposits, oxidizing gases, and temperature cycling stress. • chemical industries – Ideal for ammonia synthesis, methanol production, and gas reforming systems exposed to thermal shock and oxidizing media. • metal and glass manufacturing – Protects curved tubes in furnaces and preheaters exposed to abrasive and high-heat environments. Conclusion The 1Cr20Ni14Si2 U Type Half Round Tube Shield by Ladhani Metal Corporation is a high-performance solution for protecting U-bend tube sections in the most demanding thermal and chemical environments. With excellent resistance to oxidation, carburization, and thermal fatigue, this shield is ideal for use in power plants, refineries, chemical processing units, and high-temperature industrial systems. Designed for precision fit and easy installation, it provides dependable, long-lasting protection that reduces maintenance and extends equipment service life. For technical consultation, custom orders, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-engineered components used to protect boiler and heat exchanger tubes from erosion, scaling, and high-temperature corrosion. These shields are widely applied in industrial systems exposed to thermal cycling, aggressive gases, and particulate flow. Their half-round shape allows for simple and secure installation over straight or curved tube surfaces, extending tube life and reducing maintenance needs. SS 410 U Type Half Round Tube Shield The SS 410 U Type Half Round Tube Shield is engineered for protective coverage of U-bend sections in heat exchanger coils, superheaters, and boiler return bends. Manufactured from SS 410, a hardenable martensitic stainless steel, this shield provides excellent resistance to abrasion, oxidation, and moderate corrosion. The U-type design offers tailored protection to both inner and outer arcs of tube bends—critical areas vulnerable to erosion, thermal stress, and slag buildup in high-temperature environments. • Outer U Type Half Round Tube Shield – Shields the outer curvature of the bend against high-temperature oxidation, impact wear, and flue gas turbulence. • Inner U Type Half Round Tube Shield – Protects the inner radius from scaling, corrosive gas attack, and localized erosion caused by gas flow irregularities. Ladhani Metal Corporation supplies SS 410 U Type Half Round Tube Shields designed for durability and cost-effectiveness in applications where wear resistance and thermal stability are key performance requirements. Chemical Composition of SS 410 – Martensitic Stainless Steel • Carbon (C): 0.08 – 0.15% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 11.5 – 13.5% • Nickel (Ni): ≤ 0.75% • Iron (Fe): Balance Applications: Ideal for moderate corrosion environments and high-temperature zones where mechanical strength, scaling resistance, and surface hardness are essential. Uses • Shielding U-bend tube sections in power plant superheaters and reheaters • Protection of tube bends in industrial boilers and HRSG return loops • Coverage for high-wear tube areas in WHRBs and economizers • Safeguarding of steam reformer and heat exchanger return curves in refineries • Suitable for dry, high-temperature service conditions with limited corrosive exposure Features • High surface hardness – SS 410 can be heat-treated to improve abrasion and erosion resistance, suitable for high-wear areas. • Oxidation resistance – Performs well in dry air at elevated temperatures, offering effective scaling resistance during continuous heating cycles. • Inner and outer coverage – Available in both configurations for complete U-bend protection, reducing risk of localized tube failure. • Precision fit – Fabricated to exact bend radius and tube diameter for a stable and secure installation. • Easy to install – Can be mounted using clamps, banding, or welding methods without major system modifications. • Economical option – Offers a cost-effective solution for environments where chemical corrosion is minimal but mechanical wear is high. Applications • thermal power plants – Protects U-bend tubes in reheaters and superheaters from oxidation, slag deposits, and particulate erosion. Improves thermal zone durability. • chemical and fertilizer industries – Installed in systems where temperature resistance is more critical than corrosion protection. Helps extend tube service life under cyclic heat conditions. • waste heat recovery units – Shields return bends in WHRBs and economizers exposed to hot gas streams and turbulent flow. • refinery and process heaters – Used in units with limited corrosive exposure where surface scaling and impact wear are primary concerns. • cement and metallurgical plants – Ideal for steam and gas heating lines where wear resistance at elevated temperatures is essential. Conclusion The SS 410 U Type Half Round Tube Shield from Ladhani Metal Corporation provides reliable and economical protection for U-bend tubes in heat-intensive, erosion-prone environments. With its martensitic structure and good thermal resistance, SS 410 is well-suited for applications where mechanical wear, oxidation, and surface degradation are key operational challenges. Customizable in size and bend radius, these shields deliver cost-efficient, high-performance solutions for extending tube life and reducing unplanned maintenance. For technical consultation, custom orders, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-engineered components used to protect boiler and heat exchanger tubes from erosion, scaling, and high-temperature corrosion. These shields are widely applied in industrial systems exposed to thermal cycling, aggressive gases, and particulate flow. Their half-round shape allows for simple and secure installation over straight or curved tube surfaces, extending tube life and reducing maintenance needs. SS 316L U Type Half Round Tube Shield The SS 316L U Type Half Round Tube Shield is specifically designed to offer enhanced protection to U-bend sections in heat exchangers, superheaters, and steam reformers. Fabricated from SS 316L, a low-carbon austenitic stainless steel alloyed with molybdenum, it delivers superior resistance to pitting, crevice corrosion, and intergranular attack in chloride-rich and high-temperature environments. The U-type design allows for seamless coverage of both the inner and outer arcs of tube bends, where thermal and mechanical stresses are most concentrated. • Outer U Type Half Round Tube Shield – Protects the outer bend of the tube against high-velocity gas impact, slag accumulation, and surface oxidation. • Inner U Type Half Round Tube Shield – Shields the inner curve from localized erosion, turbulence-related wear, and thermal fatigue cracking. Ladhani Metal Corporation manufactures and supplies SS 316L U Type Half Round Tube Shields for industries operating in corrosive, welded, or high-heat service conditions where enhanced durability and metallurgical stability are critical. Chemical Composition of SS 316L – Low Carbon Austenitic Stainless Steel • Carbon (C): ≤ 0.03% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Nickel (Ni): 10.0 – 14.0% • Molybdenum (Mo): 2.0 – 3.0% • Iron (Fe): Balance Applications: Specifically suited for high-chloride, welded, and high-temperature systems where corrosion resistance and thermal stability are essential. Uses • Protection of U-bend tube sections in superheaters and reheaters in thermal power plants • Coverage for return bends in chemical heat exchangers and ammonia reformers • Shielding curved tube segments in WHRBs and HRSGs exposed to thermal cycling • Corrosion and wear protection in condensers and evaporators operating with chlorides or acidic gases • Ideal for coastal, offshore, and marine installations involving saline or humid environments Features • Corrosion-resistant low carbon grade – SS 316L’s reduced carbon content ensures resistance to sensitization and intergranular corrosion after welding. • High-performance under heat – Maintains structural integrity and corrosion resistance in elevated temperature applications. • Dual-bend protection – Available in inner and outer U-type configurations to safeguard the entire arc of the U-bend. • Custom-formed profiles – Engineered to precisely fit tube diameter and bend radius for secure and stable installation. • Quick installation – Designed for easy mounting via tack welds, banding, or clamping without requiring tube disassembly. • Tailored dimensions – Manufactured in a range of thicknesses, lengths, and profiles to meet exact project needs. Applications • thermal power plants – Installed on U-bend tubes in superheaters and reheaters to mitigate scale formation and corrosion due to flue gases. Enhances heat exchanger reliability and life span. • petrochemical refineries – Used in steam reformers and exchangers handling chlorides, acids, and hydrocarbons. Ensures long-term corrosion resistance in aggressive environments. • waste heat recovery units – Protects U-shaped tubes from erosion and cracking caused by fluctuating gas velocities and slag deposits. • fertilizer and chemical plants – Shields critical tube bends from acidic or chloride-containing media in reformers and process heaters. • marine and coastal systems – Provides anti-corrosion protection in salt-laden and humid atmospheres for extended tube life. Conclusion The SS 316L U Type Half Round Tube Shield by Ladhani Metal Corporation is a robust and corrosion-resistant solution for protecting U-bend tube sections in heat-intensive and chemically aggressive systems. With its low carbon content and molybdenum enhancement, it ensures excellent resistance to pitting, scaling, and intergranular corrosion. Available in inner and outer U-bend configurations and tailored to match system specifications, these shields offer reliable, long-lasting tube protection in power, chemical, marine, and industrial sectors. For technical consultation, custom orders, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are robust, precision-fabricated protective sleeves designed to guard the outer surfaces of tubes in boilers, heat exchangers, incinerators, and high-temperature processing equipment. Engineered to extend the service life of tubes exposed to corrosive gases, abrasive particulates, and elevated temperatures, these shields provide a reliable barrier against mechanical and chemical degradation. The half-round design facilitates easy installation while ensuring a secure, form-fitting layer of defense. 1Cr13 Half Round Tube Shield The 1Cr13 Half Round Tube Shield is a semi-cylindrical component manufactured from martensitic stainless steel containing approximately 13% chromium. Classified under the 1Cr13 grade, this alloy delivers good corrosion resistance, excellent wear performance, and moderate strength at elevated temperatures. It is especially suited for thermal environments that are not extremely oxidizing or carburizing but where erosion and mechanical wear are a concern. With a higher hardness potential through heat treatment and moderate thermal resistance, 1Cr13 shields are ideal for applications involving flue gas exposure, soot-laden atmospheres, and temperature cycling. The shield’s half-round configuration is precision-engineered for optimal tube coverage and long-term durability. It offers a balance of strength, corrosion resistance, and cost-effectiveness, making it suitable for a wide range of industrial processes. Chemical Composition of 1Cr13 – Martensitic Stainless Steel • Carbon (C): 0.15 – 0.20% • Silicon (Si): ≤ 1.00% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Chromium (Cr): 12.0 – 14.0% • Nickel (Ni): ≤ 0.60% • Iron (Fe): Balance Uses • Boiler Tube Protection – Shields tube surfaces from flue gas erosion, ash particle abrasion, and soot buildup in economizers and waterwalls. • Heat Exchanger Tubes – Provides an extra layer of wear resistance in zones prone to mechanical stress and fluid turbulence. • Incinerator and Waste Heat Units – Guards tubes exposed to fluctuating temperatures, slag, and particulate deposits. • Cement Plant Piping – Protects tubing and ducts in kiln exhaust systems from abrasive dust and high flow velocity. • Air Preheaters and Recuperators – Enhances the durability of components subjected to temperature variations and corrosive gases. Features • Moderate Oxidation Resistance – Chromium content enables good performance in mildly oxidizing environments and intermittent exposure to high temperatures. • Wear and Abrasion Resistance – Martensitic structure offers high surface hardness and resistance to mechanical wear. • Heat Treatable – Can be hardened to increase durability and resistance to deformation. • Cost-Effective – Provides a lower-cost alternative to austenitic and superalloy shields for moderate service conditions. • High Dimensional Accuracy – Manufactured with tight tolerances to ensure secure fitment and uniform tube coverage. • Convenient Installation – Half-round shape enables quick mounting through welding or clamping techniques. • Versatile Finishing Options – Supplied with pickled or mechanically polished surfaces to improve corrosion resistance and adhesion. Applications • Power Generation – Used in economizer, preheater, and convection sections of boilers to prevent erosion and fouling. • Chemical and Fertilizer Plants – Protects exposed tube surfaces in systems with moderate chemical exposure. • Metallurgical Furnaces – Shields mechanical and flue components exposed to particulate movement and temperature cycling. • Pulp and Paper Industry – Used in recovery boilers and heat exchangers where corrosion resistance and mechanical strength are both required. • Petrochemical Plants – Applied in lower-temperature zones where scaling and erosion are primary concerns. Conclusion The 1Cr13 Half Round Tube Shield by Ladhani Metal Corporation provides an optimal solution for industrial tube protection in moderate temperature and corrosion environments. Its martensitic stainless steel composition ensures excellent wear resistance, good oxidation stability, and structural strength at a competitive cost. Designed for easy installation and reliable performance, these shields are ideal for various applications in power, process, and heat recovery systems. Custom-built to meet specific dimensions, material thicknesses, and finishing preferences, 1Cr13 tube shields offer dependable service life extension for critical heat transfer equipment. For technical specifications, pricing, or customization inquiries, please contact Ladhani Metal Corporation.

Ladhani Metal Corporation offers SS 316 Half Round Tube Shields designed to protect boiler tubes in power plants, HRSGs, WHRBs, and industrial steam systems. Boiler tubes often face high-temperature flue gas erosion, oxidation, and soot blower impact, which can reduce their operational life. Manufactured from molybdenum-bearing austenitic stainless steel grade SS 316, these shields provide excellent resistance to pitting, crevice corrosion, and scaling in chloride-rich and corrosive boiler atmospheres, making them highly reliable for demanding service conditions. Function of Boiler Tubes • Carry water or steam through heating sections of the boiler • Continuously exposed to high-temperature flue gases, ash, and corrosive deposits • Require Half Round Tube Shields in high-erosion, soot blower, and corrosive zones Ladhani Metal Corporation manufactures, supplies, and exports SS 316 Half Round Tube Shields in customized lengths, diameters, and thicknesses to meet diverse industrial requirements worldwide. SS 316 Grade Chemical Composition – Austenitic Stainless Steel • Carbon (C): ≤ 0.08% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.00 – 18.00% • Nickel (Ni): 10.00 – 14.00% • Molybdenum (Mo): 2.00 – 3.00% • Iron (Fe): Balance Applications: Suitable for superheater and reheater tubes in thermal power stations, waste heat recovery boilers, HRSGs, petrochemical heaters, and steam plants exposed to corrosive flue gases and high operating temperatures. Uses • Protects boiler tubes against high-temperature corrosion and erosion • Shields tubes from soot blower and abrasive particle damage • Extends service life of boiler heating components in corrosive atmospheres • Widely used in WHRBs, HRSGs, and utility boilers requiring extra corrosion resistance Features • Superior resistance to corrosion and scaling in chloride-laden boiler environments • Enhanced pitting and crevice corrosion resistance due to molybdenum content • Excellent mechanical strength and stability at elevated temperatures • Manufactured for precise fit and easy installation Applications • Power generation boilers – Reliable protection for reheater and superheater tubes • Waste heat recovery boilers – Guards tubes against erosion and flue gas deposits • Industrial steam plants – Ensures longer life in corrosive and erosive atmospheres • Petrochemical process heaters – Ideal for chloride-rich and corrosive flue gas conditions Conclusion The SS 316 Half Round Tube Shield for Boiler Tubes by Ladhani Metal Corporation delivers reliable protection against erosion, scaling, and corrosive damage in harsh boiler environments. Designed with molybdenum-enhanced stainless steel, these shields ensure long service life, reduced maintenance, and superior resistance under severe operating conditions. Available in export-ready specifications, they are a trusted solution for global power, petrochemical, and industrial sectors. For supply and technical support, contact Ladhani Metal Corporation. #Mumbai #Pune #Ahmedabad #Vadodara #Surat #Rajkot #Jamnagar #Bharuch #Ankleshwar #Vapi #Delhi #Faridabad #Ghaziabad #Noida #Gurugram #Chennai #Coimbatore #Tiruchirappalli #Hyderabad #Visakhapatnam #Vijayawada #Bangalore #Mangalore #Mysore #Kolkata #Durgapur #Asansol #Bhubaneswar #Rourkela #Raipur #Bhilai #Bilaspur #Nagpur #Nashik #Aurangabad #Indore #Bhopal #Jabalpur #Kanpur #Lucknow #Varanasi #Jaipur #Kota #Udaipur #Jodhpur #Chandigarh #Ludhiana #Jalandhar #Haridwar #Dehradun #Agra #Meerut #Aligarh #Moradabad #Bareilly #Mathura #Gwalior #Rewa #Satna #Sagar #Ujjain #Ratlam #Solapur #Kolhapur #Amravati #Akola #Jalgaon #Latur #Sangli #Nanded #Gandhinagar #Bhavnagar #Mehsana #Surendranagar #Junagadh #Nadiad #Nizamabad #Karimnagar #Warangal #Kurnool #Nellore #Tirupati #Madurai #Tirunelveli #Thoothukudi #Belgaum #Hubli #Tumkur #Sambalpur #Jamshedpur #Ranchi #Dhanbad #Patna #Muzaffarpur#halftubeshield #utypehalftubeshield #tubeshieldexporter #TubeShield #HalfTubeShield #SSHalfRoundShield #BoilerTubeShield #BoilerShield #TubeProtection #Tubeshieldmanufacturer #BoilerTubeProtection #SSTubeShield #MetalIndustry #SteelFabrication #IndustrialShielding #SS304Shield #SS316Shield #StainlessSteelShield #WeldOnShield #WeldedTubeShield #TubeCladding #BoilerTubeSleeve #TubeSleeve #MetalFabrication #PowerPlantSupplies #RefineryEquipment #ProcessIndustry #MetalComponent #TubeShieldForBoilers #BoilerParts #SteelSolutions #TubeShieldManufacturer #TubeShieldSupplier #SSShielding #IndustrialTubeShield #BoilerTubeGuard #CustomMetalParts #SteelIndustryIndia #MetalEngineering #HeavyIndustrySupply #StainlessSteelIndia #SteelExporters #MetalComponentExport #FabricatedProducts #SteelDealer #IndustrialSupplyIndia #BoilerTubeFittings #TubeShieldingSolutions #HalfTubeCover #HeatExchangerShield #HalfRoundReheaterShield #ReheaterTubeShield #BoilerReheaterProtection #PowerPlantTubeShield #BoilerErosionShield

Ladhani Metal Corporation offers SS 310 Half Round Tube Shields designed to protect boiler tubes in power plants, HRSGs, WHRBs, and industrial steam plants. Boiler tubes are subjected to extreme service conditions including high-temperature oxidation, erosive flue gases, and soot blower impact, which can reduce tube thickness and service life. Manufactured from austenitic stainless steel grade SS 310, these shields provide outstanding resistance to high-temperature oxidation, superior strength, and excellent durability under prolonged exposure to elevated temperatures. Function of Boiler Tubes • Transport water or steam through various heating sections of the boiler • Exposed to continuous flue gas erosion, oxidation, and abrasive particles • Require Half Round Tube Shields in soot blower zones and erosion-prone areas Ladhani Metal Corporation manufactures, supplies, and exports SS 310 Half Round Tube Shields in a wide range of sizes, diameters, and thicknesses to meet domestic and international industry requirements. SS 310 Grade Chemical Composition – Austenitic Stainless Steel • Carbon (C): ≤ 0.25% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.50% • Chromium (Cr): 24.00 – 26.00% • Nickel (Ni): 19.00 – 22.00% • Iron (Fe): Balance Applications: Suitable for boiler tubes in thermal power plants, waste heat recovery boilers, HRSGs, and steam systems where tubes are exposed to severe high-temperature conditions and oxidizing atmospheres. Uses • Protects boiler tubes from oxidation, erosion, and thermal stress • Shields against soot blower erosion and high-velocity flue gas streams • Enhances service life of steam circuits and boiler components • Widely used in HRSGs, WHRBs, and industrial boilers operating under extreme thermal cycles Features • Exceptional oxidation resistance up to 1100°C • Excellent mechanical strength at high temperatures • Long-lasting durability in oxidizing and carburizing atmospheres • Engineered for precise fit and ease of installation Applications • Power generation boilers – Protection for superheater and reheater tubes in extreme thermal zones • Waste heat recovery systems – Guards tubes from erosive gas streams and ash deposits • Industrial steam plants – Reliable performance under fluctuating temperature cycles • Petrochemical and refinery heaters – Suitable for high-efficiency and high-temperature sections Conclusion The SS 310 Half Round Tube Shield for Boiler Tubes by Ladhani Metal Corporation ensures long-lasting protection under extreme boiler operating conditions. With high oxidation resistance, mechanical strength, and durability, these shields reduce wear, extend tube service life, and minimize maintenance downtime. Available in export-ready specifications, they are the preferred choice for global power, steam, and process industries. For technical details and supply inquiries, contact Ladhani Metal Corporation. #Mumbai #Pune #Ahmedabad #Vadodara #Surat #Rajkot #Jamnagar #Bharuch #Ankleshwar #Vapi #Delhi #Faridabad #Ghaziabad #Noida #Gurugram #Chennai #Coimbatore #Tiruchirappalli #Hyderabad #Visakhapatnam #Vijayawada #Bangalore #Mangalore #Mysore #Kolkata #Durgapur #Asansol #Bhubaneswar #Rourkela #Raipur #Bhilai #Bilaspur #Nagpur #Nashik #Aurangabad #Indore #Bhopal #Jabalpur #Kanpur #Lucknow #Varanasi #Jaipur #Kota #Udaipur #Jodhpur #Chandigarh #Ludhiana #Jalandhar #Haridwar #Dehradun #Agra #Meerut #Aligarh #Moradabad #Bareilly #Mathura #Gwalior #Rewa #Satna #Sagar #Ujjain #Ratlam #Solapur #Kolhapur #Amravati #Akola #Jalgaon #Latur #Sangli #Nanded #Gandhinagar #Bhavnagar #Mehsana #Surendranagar #Junagadh #Nadiad #Nizamabad #Karimnagar #Warangal #Kurnool #Nellore #Tirupati #Madurai #Tirunelveli #Thoothukudi #Belgaum #Hubli #Tumkur #Sambalpur #Jamshedpur #Ranchi #Dhanbad #Patna #Muzaffarpur#halftubeshield #utypehalftubeshield #tubeshieldexporter #TubeShield #HalfTubeShield #SSHalfRoundShield #BoilerTubeShield #BoilerShield #TubeProtection #Tubeshieldmanufacturer #BoilerTubeProtection #SSTubeShield #MetalIndustry #SteelFabrication #IndustrialShielding #SS304Shield #SS316Shield #StainlessSteelShield #WeldOnShield #WeldedTubeShield #TubeCladding #BoilerTubeSleeve #TubeSleeve #MetalFabrication #PowerPlantSupplies #RefineryEquipment #ProcessIndustry #MetalComponent #TubeShieldForBoilers #BoilerParts #SteelSolutions #TubeShieldManufacturer #TubeShieldSupplier #SSShielding #IndustrialTubeShield #BoilerTubeGuard #CustomMetalParts #SteelIndustryIndia #MetalEngineering #HeavyIndustrySupply #StainlessSteelIndia #SteelExporters #MetalComponentExport #FabricatedProducts #SteelDealer #IndustrialSupplyIndia #BoilerTubeFittings #TubeShieldingSolutions #HalfTubeCover #HeatExchangerShield #HalfRoundReheaterShield #ReheaterTubeShield #BoilerReheaterProtection #PowerPlantTubeShield #BoilerErosionShield #SteamBoilerTubeShield #HighTempTubeShield #BoilerWearProtection