Ladhani Metal Corporation offers 1Cr13 Half Round Tube Shields designed to protect reheater (R/H) tubes in boilers, power plants, and industrial steam systems. Reheater tubes carry steam through the reheater section of the boiler, where it is reheated after partial expansion in the high-pressure turbine to improve efficiency and minimize moisture formation. Manufactured from martensitic stainless steel grade 1Cr13, these shields provide good mechanical strength, oxidation resistance, and reliable protection against erosion and wear in high-temperature boiler environments. Function of R/H Tubes • Carry steam through the reheater section of the boiler • Exposed to very high temperatures (often > 540°C) and erosion from flue gases • Often protected with Half Round Tube Shields in high-velocity and ash-laden zones Ladhani Metal Corporation manufactures, supplies, and exports 1Cr13 Half Round Tube Shields in a variety of lengths, diameters, and thicknesses to meet both domestic and international requirements. 1Cr13 Grade Chemical Composition – Martensitic Stainless Steel • Carbon (C): ≤ 0.15% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 12.00 – 14.00% • Nickel (Ni): ≤ 0.60% • Iron (Fe): Balance Applications: Well-suited for reheater tubes in thermal power plants, industrial steam plants, and boilers requiring strong mechanical performance with moderate corrosion and oxidation resistance. Uses • Shields reheater tubes from erosion and flue gas oxidation • Protects against soot blower impact and abrasive ash particles • Extends service life of steam circuit components under elevated temperatures • Commonly used in WHRBs, HRSGs, and industrial boilers Features • Strong mechanical strength at high temperatures • Moderate oxidation and corrosion resistance in boiler atmospheres • Cost-effective solution for erosion-prone areas • Manufactured for precise fit and easy installation Applications • Power generation boilers – Protection for reheater sections exposed to erosion • Waste heat recovery boilers – Guards tubes from abrasive gas flows • Industrial steam systems – Reliable under medium-to-high temperature cycles • Process boilers – Provides extended service life in erosive conditions Conclusion The 1Cr13 Half Round Tube Shield for Reheater (R/H) Tubes by Ladhani Metal Corporation provides durable, cost-effective protection for boiler tubes exposed to erosion and high-temperature oxidation. Designed for precision fit and long service life, these shields are available in a wide range of export-ready specifications. For supply and technical inquiries, contact Ladhani Metal Corporation. #Mumbai #Pune #Ahmedabad #Vadodara #Surat #Rajkot #Jamnagar #Bharuch #Ankleshwar #Vapi #Delhi #Faridabad #Ghaziabad #Noida #Gurugram #Chennai #Coimbatore #Tiruchirappalli #Hyderabad #Visakhapatnam #Vijayawada #Bangalore #Mangalore #Mysore #Kolkata #Durgapur #Asansol #Bhubaneswar #Rourkela #Raipur #Bhilai #Bilaspur #Nagpur #Nashik #Aurangabad #Indore #Bhopal #Jabalpur #Kanpur #Lucknow #Varanasi #Jaipur #Kota #Udaipur #Jodhpur #Chandigarh #Ludhiana #Jalandhar #Haridwar #Dehradun #Agra #Meerut #Aligarh #Moradabad #Bareilly #Mathura #Gwalior #Rewa #Satna #Sagar #Ujjain #Ratlam #Solapur #Kolhapur #Amravati #Akola #Jalgaon #Latur #Sangli #Nanded #Gandhinagar #Bhavnagar #Mehsana #Surendranagar #Junagadh #Nadiad #Nizamabad #Karimnagar #Warangal #Kurnool #Nellore #Tirupati #Madurai #Tirunelveli #Thoothukudi #Belgaum #Hubli #Tumkur #Sambalpur #Jamshedpur #Ranchi #Dhanbad #Patna #Muzaffarpur#halftubeshield #utypehalftubeshield #tubeshieldexporter #TubeShield #HalfTubeShield #SSHalfRoundShield #BoilerTubeShield #BoilerShield #TubeProtection #Tubeshieldmanufacturer #BoilerTubeProtection #SSTubeShield #MetalIndustry #SteelFabrication #IndustrialShielding #SS304Shield #SS316Shield #StainlessSteelShield #WeldOnShield #WeldedTubeShield #TubeCladding #BoilerTubeSleeve #TubeSleeve #MetalFabrication #PowerPlantSupplies #RefineryEquipment #ProcessIndustry #MetalComponent #TubeShieldForBoilers #BoilerParts #SteelSolutions #TubeShieldManufacturer #TubeShieldSupplier #SSShielding #IndustrialTubeShield #BoilerTubeGuard #CustomMetalParts #SteelIndustryIndia #MetalEngineering #HeavyIndustrySupply #StainlessSteelIndia #SteelExporters #MetalComponentExport #FabricatedProducts #SteelDealer #IndustrialSupplyIndia #BoilerTubeFittings #TubeShieldingSolutions #HalfTubeCover #HeatExchangerShield #HalfRoundReheaterShield #ReheaterTubeShield #BoilerReheaterProtection #PowerPlantTubeShield #BoilerErosionShield #SteamBoilerTubeShield #HighTempTubeShield #BoilerWearProtection

Ladhani Metal Corporation offers SS 430 Half Round Tube Shields specially designed to protect reheater (R/H) tubes in boilers, power plants, and industrial steam systems. Reheater tubes carry steam through the reheater section of the boiler, where it is reheated after partial expansion in the high-pressure turbine to improve efficiency and minimize moisture. Manufactured from ferritic stainless steel grade SS 430, these shields provide excellent resistance to oxidation, scaling, and moderate corrosion while offering good thermal conductivity and formability for long-term service in demanding boiler environments. Function of R/H Tubes • Carry steam through the reheater section of the boiler • Exposed to very high temperatures (often > 540°C) and erosion from flue gases • Often protected with Half Round Tube Shields in high-velocity and ash-laden zones Ladhani Metal Corporation manufactures, supplies, and exports SS 430 Half Round Tube Shields in different lengths, diameters, and thicknesses, ensuring suitability for a wide range of domestic and international boiler applications. SS 430 Grade Chemical Composition – Ferritic Stainless Steel • Carbon (C): ≤ 0.12% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.00 – 18.00% • Nickel (Ni): ≤ 0.50% • Iron (Fe): Balance Applications: Commonly used in reheater sections of thermal power plants, waste heat recovery boilers (WHRBs), and heat recovery steam generators (HRSGs) where scaling resistance and cost-effective protection are required. Uses • Shields reheater tubes against erosion, scaling, and oxidation • Protects R/H tubes in zones exposed to high flue gas velocity and ash particles • Extends tube service life under thermal cycling and corrosive atmospheres • Applicable in utility boilers, WHRBs, HRSGs, and process steam plants Features • Excellent resistance to oxidation and scaling at elevated temperatures • Cost-effective protection with good mechanical strength • Superior thermal conductivity for stable heat transfer • Custom-fit design for precise installation and maximum coverage Applications • Power generation boilers – Reheater tube protection in oxidizing atmospheres • Waste heat recovery systems – Reliable shield against particle erosion • Industrial boilers – Durable under varying flue gas conditions • Petrochemical and process plants – Efficient in moderate corrosive service environments Conclusion The SS 430 Half Round Tube Shield for Reheater (R/H) Tubes by Ladhani Metal Corporation offers dependable, cost-effective protection against scaling, oxidation, and erosion in high-temperature boiler conditions. With good mechanical strength and precision fit, these shields reduce maintenance needs and extend tube service life. Available in customized, export-ready specifications to meet global industry requirements. For supply and technical assistance, contact Ladhani Metal Corporation. #Mumbai #Pune #Ahmedabad #Vadodara #Surat #Rajkot #Jamnagar #Bharuch #Ankleshwar #Vapi #Delhi #Faridabad #Ghaziabad #Noida #Gurugram #Chennai #Coimbatore #Tiruchirappalli #Hyderabad #Visakhapatnam #Vijayawada #Bangalore #Mangalore #Mysore #Kolkata #Durgapur #Asansol #Bhubaneswar #Rourkela #Raipur #Bhilai #Bilaspur #Nagpur #Nashik #Aurangabad #Indore #Bhopal #Jabalpur #Kanpur #Lucknow #Varanasi #Jaipur #Kota #Udaipur #Jodhpur #Chandigarh #Ludhiana #Jalandhar #Haridwar #Dehradun #Agra #Meerut #Aligarh #Moradabad #Bareilly #Mathura #Gwalior #Rewa #Satna #Sagar #Ujjain #Ratlam #Solapur #Kolhapur #Amravati #Akola #Jalgaon #Latur #Sangli #Nanded #Gandhinagar #Bhavnagar #Mehsana #Surendranagar #Junagadh #Nadiad #Nizamabad #Karimnagar #Warangal #Kurnool #Nellore #Tirupati #Salem #Erode #Madurai #Tirunelveli #Thoothukudi #Belgaum #Hubli #Tumkur #Hassan #Cuttack #Sambalpur #Jamshedpur #Ranchi #Dhanbad #Patna #Gaya #Muzaffarpur#halftubeshield #utypehalftubeshield #tubeshieldexporter #TubeShield #HalfTubeShield #SSHalfRoundShield #BoilerTubeShield #BoilerShield #TubeProtection #Tubeshieldmanufacturer #BoilerTubeProtection #SSTubeShield #MetalIndustry #SteelFabrication #IndustrialShielding #SS304Shield #SS316Shield #StainlessSteelShield #WeldOnShield #WeldedTubeShield #TubeCladding #BoilerTubeSleeve #TubeSleeve #MetalFabrication #PowerPlantSupplies #RefineryEquipment #ProcessIndustry #MetalComponent #TubeShieldForBoilers #BoilerParts #SteelSolutions #TubeShieldManufacturer #TubeShieldSupplier #SSShielding #IndustrialTubeShield #BoilerTubeGuard #CustomMetalParts #SteelIndustryIndia #MetalEngineering #HeavyIndustrySupply #StainlessSteelIndia #SteelExporters #MetalComponentExport #FabricatedProducts #SteelDealer #IndustrialSupplyIndia #BoilerTubeFittings #TubeShieldingSolutions #HalfTubeCover #HeatExchangerShield #HalfRoundReheaterShield #ReheaterTubeShield #BoilerReheaterProtection #PowerPlantTubeShield #BoilerErosionShield #SteamBoilerTubeShield #HighTempTubeShield #BoilerWearProtection

Ladhani Metal Corporation offers SS 430 Outer Half Round 90 Degree Bend Tube Shields designed to protect the outer arc of U-bend and 90-degree curved tubes in boilers, heat exchangers, superheaters, and reheaters. Manufactured from ferritic stainless steel grade SS 430, these shields provide good corrosion resistance, excellent formability, and thermal stability in moderately aggressive service environments. SS 430 is particularly suitable for applications where resistance to oxidation and surface scaling is needed without exposure to highly corrosive agents. The semi-cylindrical profile is precision-formed to match the outer curvature of return tube bends, offering a physical barrier against soot-blower impact, flue gas erosion, and ash particle wear. SS 430 shields are commonly used in utility and industrial boilers operating under dry, mildly corrosive, and thermally demanding conditions. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of SS 430 Outer Half Round 90 Degree Bend Tube Shields, offering custom configurations to suit specific plant layouts and service requirements. SS 430 Grade Chemical Composition – Ferritic Stainless Steel • Carbon (C): ≤ 0.12% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Nickel (Ni): ≤ 0.75% • Iron (Fe): Balance Applications: Ideal for power plants, WHRBs, HRSGs, and general industrial systems requiring protection for tube bends in dry heat and oxidizing environments. Uses • Shielding outer 90-degree bends in superheaters and reheaters • Applied in WHRBs and HRSG return coils exposed to dry flue gas • Protects against moderate erosion and oxidation in utility boilers • Suitable for curved tubes in industrial furnaces and heat recovery units Features • Cost-effective protection – Combines durability with economical material choice • Oxidation resistance – Performs well in clean flue gas and dry heat exposure • Thermal reliability – Withstands repeated heating cycles without deformation • Custom-fit geometry – Formed to match exact bend radius for tight coverage • Versatile installation – Can be clamped, banded, or tack welded as needed • Multiple sizes – Offered in a variety of thicknesses, lengths, and radii Applications • Thermal power stations – Shields steam lines and return bends from surface scaling • Waste heat boilers – Guards tube bends in clean gas recovery systems • Process heaters – Used in less corrosive gas heating environments • Cement and food processing industries – Protects tube curves from oxidation Conclusion The SS 430 Outer Half Round 90 Degree Bend Tube Shield by Ladhani Metal Corporation provides durable and cost-efficient protection for tube bends exposed to dry heat, oxidation, and moderate wear. With good formability and thermal performance, these shields are ideal for systems where corrosion levels are controlled but mechanical shielding is essential. For custom sizing, material selection, or technical specifications, contact Ladhani Metal Corporation. #Mumbai #Pune #Ahmedabad #Vadodara #Surat #Rajkot #Jamnagar #Bharuch #Ankleshwar #Vapi #Delhi #Faridabad #Ghaziabad #Noida #Gurugram #Chennai #Coimbatore #Tiruchirappalli #Hyderabad #Visakhapatnam #Vijayawada #Bangalore #Mangalore #Mysore #Kolkata #Durgapur #Asansol #Bhubaneswar #Rourkela #Raipur #Bhilai #Bilaspur #Nagpur #Nashik #Aurangabad #Indore #Bhopal #Jabalpur #Kanpur #Lucknow #Varanasi #Jaipur #Kota #Udaipur #Jodhpur #Chandigarh #Ludhiana #Jalandhar #Haridwar #Dehradun #Agra #Meerut #Aligarh #Moradabad #Bareilly #Mathura #Gwalior #Rewa #Satna #Sagar #Ujjain #Ratlam #Solapur #Kolhapur #Amravati #Akola #Jalgaon #Latur #Sangli #Nanded #Gandhinagar #Bhavnagar #Mehsana #Surendranagar #Junagadh #Nadiad #Nizamabad #Karimnagar #Warangal #Kurnool #Nellore #Tirupati #Salem #Erode #Madurai #Tirunelveli #Thoothukudi #Belgaum #Hubli #Tumkur #Hassan #Cuttack #Sambalpur #Jamshedpur #Ranchi #Dhanbad #Patna #Gaya #Muzaffarpur #TubeShield #HalfTubeShield #SSHalfRoundShield #BoilerTubeShield #BoilerShield #TubeProtection #Tubeshieldmanufacturer #BoilerTubeProtection #SSTubeShield #MetalIndustry #SteelFabrication #IndustrialShielding #SS304Shield #SS316Shield #StainlessSteelShield #WeldOnShield #WeldedTubeShield #TubeCladding #BoilerTubeSleeve #TubeSleeve #MetalFabrication #PowerPlantSupplies #RefineryEquipment #ProcessIndustry #MetalComponent #TubeShieldForBoilers #BoilerParts #SteelSolutions #TubeShieldManufacturer #TubeShieldSupplier #SSShielding #IndustrialTubeShield #BoilerTubeGuard #CustomMetalParts #SteelIndustryIndia #MetalEngineering #HeavyIndustrySupply #StainlessSteelIndia #SteelExporters #MetalComponentExport #FabricatedProducts #SteelDealer #IndustrialSupplyIndia #BoilerTubeFittings #TubeShieldingSolutions #HalfTubeCover #HeatExchangerShield #halftubeshield #utypehalftubeshield #tubeshieldexporter

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are high-strength protective components used to shield boiler tubes, superheaters, and heat exchanger coils from ash impact, flue gas erosion, scaling, and corrosion. These shields are commonly used in thermal power plants, steam generating systems, and industrial boilers to protect tube surfaces and reduce wear in critical heat transfer zones. Their half-round profile is designed for easy installation and secure fitment over curved or straight tubes exposed to mechanical or thermal stress. SS 420 Half Round Tube Shield for LTSH Tube The SS 420 Half Round Tube Shield is manufactured from martensitic stainless steel grade 420, which is known for its high hardness, good oxidation resistance, and moderate corrosion protection. This material provides excellent wear resistance in abrasive and dry flue gas environments. It is particularly suitable for Low Temperature Superheater (LTSH) applications, where tubes are exposed to fly ash erosion, gas turbulence, and mechanical abrasion at relatively lower temperatures. SS 420 is often used where durability and strength are more critical than corrosion resistance alone. The Low Temperature Superheater (LTSH) is a section in a boiler where saturated steam from the steam drum is superheated to a moderately higher temperature before entering the high-temperature superheater stages. Positioned in areas with relatively lower flue gas temperatures, the LTSH helps improve thermal efficiency and reduces moisture content in steam. Due to constant exposure to abrasive flue gases and ash, LTSH tubes are prone to wear and require protective shielding, such as half round tube shields, to extend service life. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of SS 420 Half Round Tube Shields for LTSH applications, offering reliable protection where mechanical wear and gas erosion are of primary concern. Chemical Composition of SS 420 – Martensitic Stainless Steel • Carbon (C): 0.15 – 0.40% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 12.0 – 14.0% • Iron (Fe): Balance Applications: Best suited for dry ash, solid particulate flow, and mildly oxidizing environments in low-temperature superheater sections of boilers and industrial furnaces. Uses • Installed on LTSH tubes to protect from fly ash abrasion and soot erosion in power boilers • Shields return bends and tube banks in HRSGs and WHRBs exposed to turbulent flue gases • Used in biomass and coal-fired boilers to prevent mechanical wear and scaling on heat transfer tubes • Suitable for zones with high solid particle velocity and moderate corrosion risk • Effective in industrial and utility boilers that operate with abrasive fuels or in dry environments Features • High surface hardness – Excellent resistance to erosion, impact, and abrasion • Moderate oxidation resistance – Performs well in clean, oxidizing gas atmospheres • Precision fitment – Custom-shaped to match tube radius and curvature for secure shielding • Simple installation – Compatible with welding, clamping, or banding methods • Cost-efficient durability – Provides long service life in mechanical wear zones • Offered in varied lengths, thicknesses, and tube diameters based on application needs Applications • thermal power plants – Installed on LTSH tubes to minimize erosion and extend operational life • waste heat recovery units – Protects lower temperature coils from particulate-laden gas streams • coal-fired boilers – Shields convection sections exposed to ash and fly particles • steam generation systems – Guards heat transfer surfaces in dry, abrasive environments • biomass plants – Prevents wear from ash and unburned particulates in combustion zones Conclusion The SS 420 Half Round Tube Shield for LTSH Tube by Ladhani Metal Corporation – manufacturer, supplier, and exporter – offers strong mechanical protection and erosion resistance for superheater and boiler tubes operating in low-temperature, abrasive environments. Designed for durability and precision fit, it enhances tube longevity and system performance in thermal applications where particulate damage is a concern. For product specifications, custom sizes, or technical assistance, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-formed protective components used to shield boiler tubes, superheaters, and heat exchangers from erosion, scaling, ash impact, and corrosion. Commonly applied in power plants, waste heat recovery units, and industrial heating systems, these shields help prolong tube service life and maintain consistent thermal performance. Their half-round design ensures easy installation over exposed tube surfaces and provides dependable coverage in harsh gas flow zones. SS 310 Half Round Tube Shield for LTSH Tube The SS 310 Half Round Tube Shield is fabricated from high-temperature austenitic stainless steel grade 310. Known for its high chromium and nickel content, SS 310 offers excellent oxidation resistance, superior thermal stability, and strength under prolonged heat exposure. This makes it ideal for Low Temperature Superheater (LTSH) applications, where tubes are vulnerable to erosion, ash buildup, and gas-phase corrosion. The shield is precisely shaped to match the outer curvature of LTSH tubes, enabling effective surface protection in relatively low-temperature flue gas environments. The Low Temperature Superheater (LTSH) is a section in a boiler where saturated steam from the steam drum is superheated to a moderately higher temperature before entering the high-temperature superheater stages. Positioned in areas with relatively lower flue gas temperatures, the LTSH helps improve thermal efficiency and reduces moisture content in steam. Due to constant exposure to abrasive flue gases and ash, LTSH tubes are prone to wear and require protective shielding, such as half round tube shields, to extend service life. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of SS 310 Half Round Tube Shields for LTSH tubes, offering high-performance protection in demanding thermal conditions. Chemical Composition of SS 310 – Austenitic Stainless Steel • Carbon (C): ≤ 0.25% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.50% • Chromium (Cr): 24.0 – 26.0% • Nickel (Ni): 19.0 – 22.0% • Iron (Fe): Balance Applications: Designed for low-temperature superheater zones and other areas with moderate heat and flue gas exposure, where oxidation resistance and strength are required. Uses • Installed on LTSH tubes to protect against soot erosion, scaling, and ash particle wear • Applied in convection zones of power boilers and economizers exposed to moderate heat and flue gases • Suitable for WHRBs and HRSGs where return tube surfaces are vulnerable to thermal degradation • Used in process heaters and chemical boilers operating under oxidizing conditions • Effective in gas-fired and coal-fired systems where moisture and ash corrosion is common Features • Excellent oxidation resistance – Performs well in oxidizing and mildly corrosive gas atmospheres • High-temperature strength – Resists deformation and scaling under continuous heat exposure • Custom-fit design – Precisely fabricated to match specific LTSH tube sizes and geometries • Easy installation – Can be attached using clamp-on, banding, or tack welding methods • Reduces maintenance – Protects high-wear areas from erosion and thermal stress • Available in various lengths, wall thicknesses, and radii per design requirements Applications • thermal power stations – Applied on LTSH tube surfaces to resist flue gas and ash-induced damage • waste heat recovery systems – Used in lower temperature zones of WHRBs to prevent erosion • petrochemical processing – Shields tube surfaces in heaters and exchangers from scaling • utility boilers – Protects steam superheater tubes in moderate heat and corrosive conditions • industrial steam systems – Enhances tube durability in superheaters and economizer banks Conclusion The SS 310 Half Round Tube Shield for LTSH Tube by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a reliable, heat-resistant solution for protecting superheater tubes in flue gas environments with moderate temperatures. Its superior resistance to scaling, oxidation, and erosion makes it ideal for maintaining the efficiency and longevity of boiler systems operating in low-temperature zones. For custom sizes, specifications, or technical assistance, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are designed to provide surface protection for boiler tubes, superheaters, and heat exchangers from erosion, slag deposition, and thermal wear. These shields are commonly used in low temperature superheaters (LTSH), economizers, and coil sections in power plants and industrial heating systems. Their half-round profile allows quick installation on exposed tube surfaces, ensuring prolonged tube service life and reduced maintenance frequency. SS 304 Half Round Tube Shield for LTSH Tube The SS 304 Half Round Tube Shield is manufactured from austenitic stainless steel grade 304, which offers excellent corrosion resistance, good mechanical strength, and thermal stability. Designed specifically for LTSH (Low Temperature Super Heater) applications, it protects the exposed surfaces of tubes from low-temperature corrosion, soot erosion, and gas flow damage. The shield is precisely fabricated to match the outer diameter of LTSH tubes, enabling a tight and reliable fit. The Low Temperature Superheater (LTSH) is a section in a boiler where saturated steam from the steam drum is superheated to a moderately higher temperature before entering the high-temperature superheater stages. Positioned in areas with relatively lower flue gas temperatures, the LTSH helps improve thermal efficiency and reduces moisture content in steam. Due to constant exposure to abrasive flue gases and ash, LTSH tubes are prone to wear and require protective shielding, such as half round tube shields, to extend service life. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of SS 304 Half Round Tube Shields for LTSH applications, delivering durable and performance-oriented shielding solutions for thermal power and industrial process systems. Chemical Composition of SS 304 – Austenitic Stainless Steel • Carbon (C): ≤ 0.08% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 18.0 – 20.0% • Nickel (Ni): 8.0 – 10.5% • Iron (Fe): Balance Applications: Ideal for low-temperature zones in superheaters, economizers, and other heat exchange systems exposed to gas flow, corrosion, and mild scaling. Uses • Installed on LTSH tubes in power plant boilers to protect from low-temperature flue gas corrosion • Shields exposed tube sections in economizers, air preheaters, and convection coil banks • Used in heat exchangers and process heaters operating in mildly corrosive and low thermal environments • Suitable for protection in industrial boilers and steam generation systems • Applied in thermal units where soot, slag, or flue gas turbulence causes mechanical surface wear Features • Excellent corrosion resistance – Resists oxidation, acidic gas exposure, and low-temperature fouling • Custom fit – Fabricated to match the exact diameter and length of LTSH tubes • Easy installation – Can be mounted using clamp-on, tack welding, or banding methods • Moderate thermal stability – Maintains structural integrity in low to moderate heat zones • Reduces maintenance – Prevents erosion and pitting, extending tube service life • Available in various lengths, wall thicknesses, and radii as per system specifications Applications • thermal power plants – Installed on LTSH tube banks to guard against flue gas corrosion and surface damage • industrial steam systems – Shields exposed superheater and reheater tube sections • waste heat recovery – Used in lower temperature zones of WHRBs and HRSGs • chemical plants – Provides surface protection in convection and heating coils exposed to process gases • boiler maintenance – Ideal for tube protection during retrofits, upgrades, or preventive maintenance Conclusion The SS 304 Half Round Tube Shield for LTSH Tube by Ladhani Metal Corporation – manufacturer, supplier, and exporter – offers dependable and corrosion-resistant protection for tubes in low-temperature superheater applications. With excellent mechanical and chemical performance, this shield ensures efficient operation and extended tube life in a wide range of thermal and industrial systems. For custom dimensions, technical support, or pricing, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-engineered components used to protect tubes in boilers, heat exchangers, and high-temperature process systems. Designed to reduce tube erosion, oxidation, and thermal fatigue, these shields play a critical role in maintaining the longevity and reliability of industrial equipment in thermally aggressive and corrosive environments. Cr23Ni13 Half Round Tube Shield The Cr23Ni13 Half Round Tube Shield is a semi-cylindrical protective sleeve manufactured from high-alloy stainless steel containing approximately 23% chromium and 13% nickel. This alloy provides excellent resistance to high-temperature oxidation, scaling, and corrosion, particularly in systems operating up to 1000°C. With an austenitic microstructure, Cr23Ni13 exhibits good strength, ductility, and resistance to thermal shock, making it ideal for use in heat-intensive industrial processes. The half-round shape allows for easy installation over existing tubes, creating a strong and secure shield against gas flow, flame impingement, and particulate erosion. Chemical Composition of Cr23Ni13 – Austenitic Heat-Resistant Stainless Steel • Carbon (C): ≤ 0.12% • Silicon (Si): ≤ 1.50% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.040% • Sulfur (S): ≤ 0.030% • Chromium (Cr): 22.0 – 24.0% • Nickel (Ni): 12.0 – 14.0% • Iron (Fe): Balance Uses • Superheater and Reheater Tube Protection – Prevents scaling and oxidation on boiler tubes exposed to high flue gas temperatures in thermal power stations. • Furnace Tube Shielding – Shields radiant and convection tubes from flame impingement, heat distortion, and thermal fatigue in process furnaces. • Heat Exchanger Tubes – Offers external protection against erosion and scaling in petrochemical and refining systems operating with hot gases. • Power and Steam Generation Systems – Used to protect steam tubing from oxidation and surface wear in continuous service at elevated temperatures. • Industrial Kilns and Incinerators – Guards exposed piping in rotary kilns and combustion chambers against corrosive deposits and heat damage. Features • High-Temperature Resistance – Performs reliably in continuous service up to 1000°C, maintaining strength and dimensional stability. • Oxidation and Scaling Protection – Chromium-rich composition creates a protective oxide layer that resists corrosion in oxidizing environments. • Austenitic Microstructure – Provides good mechanical strength, thermal expansion resistance, and excellent ductility under heat cycling. • Precision Half-Round Form – Designed for fast, secure installation over round tubes using welding or clamping techniques. • Durable Construction – Withstands vibration, thermal shock, and erosive gas flow common in industrial boilers and furnaces. • Custom Manufacturing – Offered in various diameters, wall thicknesses, and lengths to match specific application demands. • Optional Finishes – Available in pickled, passivated, or bright annealed surface finishes based on environmental and operational needs. Applications • Thermal and Utility Boilers – Shields superheater and economizer tubes from high-temperature corrosion and ash erosion. • Petrochemical Plants – Used in process heaters and reactors where external tube surfaces are exposed to oxidizing or carburizing atmospheres. • Refineries – Protects tubes in fired heaters and reformers against oxidation and mechanical degradation. • Waste-to-Energy Facilities – Guards boiler tubes from hot flue gas erosion and acidic gas corrosion in incineration systems. • Metallurgical Furnaces – Applied in steel and non-ferrous heat treatment plants to prevent oxidation and scale accumulation. • Cement and Lime Plants – Protects gas ducting and tube banks in preheaters, coolers, and flue recovery systems from abrasive dust and heat exposure. Conclusion The Cr23Ni13 Half Round Tube Shield by Ladhani Metal Corporation offers a reliable and efficient solution for tube protection in high-temperature and oxidizing environments. Its austenitic stainless steel composition ensures superior oxidation resistance, structural integrity, and longevity under continuous thermal stress. Whether used in boilers, furnaces, or reformers, these shields effectively reduce downtime, maintenance costs, and the risk of unexpected tube failures. With flexible customization, quality-controlled fabrication, and proven material performance, Ladhani Metal Corporation remains a trusted supplier of advanced shielding solutions for critical industrial applications. For detailed specifications, customization requests, or to obtain a quote, please contact Ladhani Metal Corporation.

DIN 2634 carbon steel flanges PN 25 are high-strength weld neck flanges manufactured according to the DIN 2634 standard. Specifically designed for use in high-pressure piping systems operating up to 25 bar (362 psi), these flanges offer excellent mechanical performance and are suitable for a wide range of industrial applications. Manufactured from quality carbon steel, they provide strong, durable, and cost-effective solutions for systems where corrosion resistance requirements are moderate but structural integrity is critical. Ladhani Metal Corporation is a recognized manufacturer and global supplier of carbon steel flanges, known for precision engineering, strict adherence to international standards, and advanced production capabilities. Each flange is subject to comprehensive testing and inspection to ensure reliability and consistent performance under demanding operating conditions. Pressure Rating: • PN 25 (25 bar / 362 psi): Suitable for medium to high-pressure applications where strength and impact resistance are essential. Flange Type: • Weld Neck Flanges Designed with a tapered hub to ensure smooth transition from flange to pipe, weld neck flanges are ideal for systems experiencing frequent thermal cycling, pressure fluctuations, and mechanical stress. • Flat Face (FF) Flanges Recommended for use with gaskets made from soft materials or when connecting to cast iron components, flat face flanges ensure even gasket compression and reliable sealing performance. Carbon Steel Grades and Typical Composition: Carbon Steel (ASTM A105 / C22.8 equivalent) – Forged Carbon Steel • Carbon (C): ≤ 0.35% • Manganese (Mn): 0.60 – 1.05% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.040% • Silicon (Si): 0.10 – 0.35% • Iron (Fe): Balance Applications: Commonly used in oil and gas, petrochemical, water transmission, and power generation industries, especially in applications where high mechanical strength and pressure handling are more critical than corrosion resistance. Applications of DIN 2634 Carbon Steel Flanges PN 25: • Oil and Gas Pipelines Widely used in upstream and downstream systems for fluid transport under high pressure. • Petrochemical and Refining Plants Efficiently handles high-pressure flow systems involving hydrocarbons and steam. • Power Plants and Boiler Systems Suited for high-pressure steam and water lines, offering excellent tensile strength and fatigue resistance. • Water and Wastewater Infrastructure Used in municipal and industrial pipelines requiring cost-effective, robust flange connections. • General Industrial Systems Applicable in a wide range of mechanical systems and processing plants handling non-corrosive or mildly corrosive media. Key Features: • Compliant with DIN 2634 pressure and dimensional standards • PN 25 rating ensures compatibility with high-pressure pipelines • High tensile and yield strength for demanding structural requirements • Weld neck design enhances resistance to vibration and thermal expansion • Cost-effective solution for pressure-bearing connections • Available in standard and custom sizes, surface finishes, and pressure ratings • Heat treatment and coating options available upon request Conclusion: DIN 2634 carbon steel flanges PN 25 from Ladhani Metal Corporation provide a robust and economical solution for high-pressure systems where mechanical performance is essential. Their strength, reliability, and adaptability make them a preferred choice across industries such as oil and gas, power generation, and water infrastructure. For technical specifications, custom configurations, or pricing, contact Ladhani Metal Corporation today.

DIN 2633 super duplex steel flanges PN 16 are high-performance weld neck flanges manufactured in accordance with the DIN 2633 standard. Engineered for medium-pressure piping systems with a pressure rating of up to 16 bar (232 psi), these flanges are made from super duplex stainless steels, which offer a superior combination of high mechanical strength and outstanding corrosion resistance. They are specifically designed for critical applications in aggressive environments where standard stainless or duplex steels may not provide sufficient durability. Ladhani Metal Corporation is a globally recognized manufacturer and supplier of super duplex steel flanges, known for precision manufacturing, strict quality control, and compliance with international material and dimensional standards. Each flange is tested for performance, safety, and resistance to harsh operating conditions. Pressure Rating: • PN 16 (16 bar / 232 psi): Suitable for systems requiring secure, corrosion-resistant, and high-strength connections under moderate pressure. Flange Type: • Weld Neck Flanges Featuring a long tapered hub, these flanges offer optimal stress distribution, reduce turbulence at the joint, and ensure reliable pipe alignment in high-stress environments. • Flat Face (FF) Flanges Designed for uniform gasket compression, particularly effective when used with soft gaskets or cast iron mating components. Super Duplex Steel Grades and Full Composition: Super Duplex 2507 (UNS S32750) • Chromium (Cr): 24.0 – 26.0% • Nickel (Ni): 6.0 – 8.0% • Molybdenum (Mo): 3.0 – 5.0% • Nitrogen (N): 0.24 – 0.32% • Manganese (Mn): ≤ 1.2% • Silicon (Si): ≤ 0.8% • Carbon (C): ≤ 0.03% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.02% • Iron (Fe): Balance Applications: Ideal for offshore platforms, subsea systems, desalination plants, chemical process systems, and high-chloride environments requiring superior corrosion and pitting resistance. Super Duplex S32760 • Chromium (Cr): 24.0 – 26.0% • Nickel (Ni): 6.0 – 8.0% • Molybdenum (Mo): 3.0 – 4.0% • Tungsten (W): 0.5 – 1.0% • Copper (Cu): 0.5 – 1.0% • Nitrogen (N): 0.2 – 0.3% • Carbon (C): ≤ 0.03% • Iron (Fe): Balance Applications: Commonly used in seawater systems, heat exchangers, fire-fighting systems, and oil & gas equipment due to excellent resistance to erosion, stress corrosion cracking, and fatigue. Applications of DIN 2633 Super Duplex Steel Flanges PN 16: • Offshore Oil and Gas Platforms Resists chloride-induced corrosion and high mechanical loads in topside and subsea installations. • Desalination and Marine Systems Performs well in high-salinity environments where other alloys may suffer from pitting or crevice corrosion. • Chemical and Petrochemical Plants Suitable for handling strong acids, caustic solutions, and oxidizing environments at elevated temperatures and pressures. • Fire Protection and Water Injection Systems Ensures reliability and corrosion resistance in safety-critical and high-pressure fluid delivery systems. • Pulp and Paper Industry Used in bleach plant systems and recovery boilers where exposure to corrosive agents is routine. Key Features: • Manufactured in compliance with DIN 2633 standards • PN 16 pressure rating for medium-pressure service • Weld neck design ensures secure, vibration-resistant connections • Available in high-strength super duplex grades S32750 and S32760 • Excellent resistance to pitting, crevice corrosion, and stress corrosion cracking • High mechanical strength and fatigue resistance • Custom sizes, coatings, and pressure classes available upon request Conclusion: DIN 2633 super duplex steel flanges PN 16 from Ladhani Metal Corporation are designed to meet the most demanding operational requirements in highly corrosive and high-pressure environments. With unmatched strength and corrosion resistance, these flanges are ideal for offshore, marine, chemical, and industrial applications. For technical specifications, custom designs, or pricing information, contact Ladhani Metal Corporation today.