Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are designed to protect boiler coils, heat exchanger tubes, and superheaters from erosion, scaling, slag deposition, and high-temperature damage. These shields are used extensively in thermal power plants, waste heat recovery systems, and process industries to extend tube life, reduce maintenance costs, and maintain thermal efficiency. Their semi-cylindrical design allows for easy and secure installation over straight or curved tube surfaces. 1Cr13 U Type Inner Half Round Tube Shield The 1Cr13 U Type Inner Half Round Tube Shield is fabricated from martensitic stainless steel 1Cr13, offering good mechanical strength, moderate corrosion resistance, and excellent wear resistance. This grade performs well in thermal systems subject to moderate chemical exposure and mechanical erosion. The inner U-type configuration is engineered to shield the inner arc of U-bend tubes, where turbulent flow, thermal cycling, and slag buildup are most intense and damaging. • Inner U Type Half Round Tube Shield – Covers the internal curvature of U-bend tubes, protecting against erosion, slag impact, and thermal degradation in high-flow areas. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of 1Cr13 U Type Inner Half Round Tube Shields, offering durable and cost-effective solutions for general-purpose heat protection in industrial systems. Chemical Composition of 1Cr13 – Martensitic Stainless Steel • Carbon (C): ≤ 0.15% • Manganese (Mn): ≤ 1.00% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 12.0 – 14.0% • Iron (Fe): Balance Applications: Suitable for moderately corrosive and abrasive environments with thermal exposure, where strength and erosion resistance are required. Uses • Installed on the inner arc of U-bend tubes in boilers and reheaters to resist erosion from flue gas flow • Shields inner bends in WHRBs and HRSGs subjected to scale buildup and thermal fatigue • Applied in curved tube sections of heat exchangers and evaporators operating under fluctuating temperatures • Used in process industries for protection against moderate corrosion and mechanical wear • Ideal for thermal units in power, petrochemical, and refining applications Features • Good wear and erosion resistance – Suitable for high-velocity gas flow zones • Inner arc protection – Shields critical U-bend areas where slag, turbulence, and thermal load are most severe • Moderate corrosion resistance – Performs well in mildly aggressive gas environments • Tailored fit – Custom-fabricated to match tube size and bend radius for precise protection • Easy installation – Compatible with clamp-on, weld-on, or banding methods • Cost-effective – An economical solution for routine protection of thermal system tube bends Applications • power generation – Inner U-bend protection in superheaters and economizers facing gas flow and scaling • waste heat recovery – Used in WHRBs to protect return bends from erosion and thermal damage • petrochemical processing – Applied in internal bends of steam reformers and exchangers • chemical industry – Suitable for use in reactors and thermal units operating under moderate heat and chemical exposure • industrial furnaces – Protects tube bends from slag deposits and temperature fluctuations Conclusion The 1Cr13 U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – offers reliable protection for U-bend tubes exposed to moderate thermal and erosive conditions. With its martensitic strength, wear resistance, and affordable performance, it is well-suited for a wide range of thermal and industrial process applications. For custom sizes, technical guidance, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are protective components designed to guard heat exchanger coils, boiler tubes, and superheater assemblies from erosion, high-temperature scaling, slag accumulation, and corrosion. These shields are vital in high-performance industrial systems, including power plants, refineries, and chemical process units. Their half-round shape allows easy installation on both straight and curved tubes, improving system longevity while minimizing downtime and maintenance frequency. 1Cr20Ni14Si2 U Type Inner Half Round Tube Shield The 1Cr20Ni14Si2 U Type Inner Half Round Tube Shield is manufactured using a high-temperature austenitic stainless steel alloy with enhanced chromium, nickel, and silicon content. This alloy delivers excellent oxidation resistance, thermal fatigue resistance, and structural stability at elevated temperatures. The inner U-type configuration is tailored to cover the inner arc of U-bend tubes, offering critical protection where high-velocity gas, turbulence, and slag deposits can rapidly wear or degrade tube surfaces. • Inner U Type Half Round Tube Shield – Designed to protect the inner curvature of U-bend tubes from scaling, erosion, and heat-related damage in thermal systems. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of 1Cr20Ni14Si2 U Type Inner Half Round Tube Shields, delivering high-performance shielding solutions for demanding high-temperature environments. Chemical Composition of 1Cr20Ni14Si2 – High Chromium-Nickel-Silicon Heat-Resistant Alloy • Carbon (C): ≤ 0.20% • Manganese (Mn): ≤ 1.50% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): 1.80 – 2.50% • Chromium (Cr): 19.0 – 21.0% • Nickel (Ni): 13.0 – 15.0% • Iron (Fe): Balance Applications: Ideal for continuous high-temperature operations involving oxidizing or sulfur-containing gases. Well-suited for applications requiring excellent heat resistance and minimal thermal deformation. Uses • Shields inner arcs of U-bend tubes in boilers and superheaters operating at elevated temperatures • Installed in WHRBs and HRSGs to prevent scaling, slag, and erosion in internal tube bends • Used in curved coils in reformers and process heaters exposed to hot gas and thermal cycling • Protects tube bends in chemical reactors, incinerators, and industrial furnaces from oxidation and surface degradation • Effective in systems where stability at high temperatures and resistance to carburizing and sulfidizing environments are essential Features • Excellent high-temperature performance – Withstands long-term exposure to temperatures exceeding 1000°C • Inner arc coverage – Precisely shields erosion-prone internal tube bends in critical heat transfer zones • Superior oxidation and scaling resistance – Resists corrosion in aggressive combustion gas atmospheres • Custom-fit design – Fabricated according to specified tube radii and diameters for optimal coverage and secure fit • Quick and secure installation – Compatible with clamping, banding, or tack welding methods • Long operational life – Reduces the frequency of tube failures, improving reliability and plant efficiency Applications • power plants – Installed on U-bend tubes in superheaters and reheaters facing continuous high-temperature service • petrochemical plants – Protects inner arcs of tubes in reformers and gas processing heat exchangers • waste heat recovery – Shields return bends in WHRBs and HRSGs exposed to hot flue gas and slag • thermal processing – Applied in furnaces and incinerators where hot combustion gases affect internal tube surfaces • chemical industry – Guards against oxidizing and corrosive gas damage in curved tube sections of reactors Conclusion The 1Cr20Ni14Si2 U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a robust and heat-resistant solution for protecting U-bend tubes in high-temperature and chemically aggressive conditions. Its high alloy composition, excellent thermal resistance, and customized fitment make it ideal for enhancing tube performance and reliability in critical thermal systems. For technical specifications, customized fabrication, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are engineered to protect the surfaces of boiler tubes, superheaters, and heat exchanger coils from high-temperature corrosion, erosion, slag deposition, and scaling. Widely used in power generation, petrochemical, and industrial processing systems, these shields are fabricated with a half-round profile that allows quick installation over curved or straight tube surfaces, extending service life and minimizing repair and replacement needs. Cr23Ni13 U Type Inner Half Round Tube Shield The Cr23Ni13 U Type Inner Half Round Tube Shield is manufactured from a chromium-nickel austenitic alloy known for its excellent high-temperature resistance, structural stability, and corrosion resistance. It performs reliably under continuous thermal exposure and is well-suited for systems exposed to oxidizing, carburizing, and sulfur-rich gases. The inner U-type configuration is designed specifically to shield the inner arc of U-bend tubes, which are more susceptible to localized turbulence, thermal fatigue, and scale formation. • Inner U Type Half Round Tube Shield – Covers the internal curvature of U-bend tubes, providing targeted protection from flue gas erosion, thermal scaling, and corrosion. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of Cr23Ni13 U Type Inner Half Round Tube Shields, offering precision-engineered solutions for high-performance thermal and chemical systems. Chemical Composition of Cr23Ni13 – Austenitic Heat-Resistant Steel • Carbon (C): ≤ 0.12% • Manganese (Mn): ≤ 1.50% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.50% • Chromium (Cr): 22.0 – 24.0% • Nickel (Ni): 12.0 – 14.0% • Iron (Fe): Balance Applications: Suitable for continuous exposure to high temperatures in oxidizing and chemically aggressive environments. Ideal for inner bend protection in return coil systems subjected to high thermal load and corrosive gas flow. Uses • Protects inner arcs of U-bend tubes in thermal power plant superheaters, reheaters, and economizers • Installed in WHRBs and HRSGs to resist scale and slag in return bends exposed to flue gas turbulence • Applied in steam reformers, process furnaces, and heat exchangers where inner tube surfaces face corrosive and hot gas impact • Used in chemical reactors and cracking units operating under cyclic thermal and chemical stress • Suitable for long-term protection of curved tubes in industrial combustion and heating equipment Features • High-temperature oxidation resistance – Performs in continuous service above 1000°C • Inner arc shielding – Targets protection for the most erosion-prone and heat-stressed tube area • Corrosion resistance – Withstands exposure to sulfur-rich gases, acidic vapors, and flue gas byproducts • Fabricated to specification – Available in custom sizes and bend radii for a precise fit and stable coverage • Simple installation – Can be secured using clamping, banding, or welding without disrupting the system • Extended service life – Reduces risk of tube failure, minimizes maintenance downtime, and improves system efficiency Applications • thermal and power generation – Protects inner U-bend surfaces from corrosion and erosion in steam circuits • petrochemical processing – Shields return bends in reformers and exchangers from hot process gases • waste heat recovery – Used in curved tubes of WHRBs and HRSGs for inner arc scale protection • chemical industry – Applied in reactors and thermal systems subjected to chemical vapors and high heat • furnace and incineration systems – Effective in resisting slag and gas-induced wear in industrial burners Conclusion The Cr23Ni13 U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – offers dependable inner arc protection for U-bend tubes operating in aggressive thermal and chemical environments. Its high-temperature and corrosion-resistant properties make it ideal for safeguarding critical process tubes across a range of high-performance industrial systems. For technical consultation, customized fabrication, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are essential components used to protect heat exchanger tubes, boiler coils, and superheater assemblies from erosion, scaling, slag buildup, and high-temperature corrosion. Designed with a semi-cylindrical profile, they offer easy installation over straight or curved tube surfaces. These shields play a vital role in increasing service life, reducing tube maintenance, and ensuring the efficient operation of thermal systems across power generation, chemical processing, and petrochemical industries. 1Cr25Ni20Si2 U Type Inner Half Round Tube Shield The 1Cr25Ni20Si2 U Type Inner Half Round Tube Shield is fabricated from a high-temperature resistant chromium-nickel-silicon alloy steel. This grade offers excellent resistance to oxidation, sulfur corrosion, and thermal fatigue, even under prolonged exposure to temperatures above 1000°C. The inner U-type configuration is specifically designed to shield the internal curvature of U-bend tubes, a zone vulnerable to accelerated wear caused by flue gas turbulence, slag impact, and thermal cycling. • Inner U Type Half Round Tube Shield – Designed to cover the inside arc of U-bend tubes, offering protection from erosion, scale formation, and heat stress. Ladhani Metal Corporation is a reliable manufacturer, supplier, and exporter of 1Cr25Ni20Si2 U Type Inner Half Round Tube Shields, providing high-performance protective solutions for extreme temperature and chemically aggressive environments. Chemical Composition of 1Cr25Ni20Si2 – High Temperature Alloy Steel • Carbon (C): ≤ 0.20% • Manganese (Mn): ≤ 1.50% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): 1.80 – 2.50% • Chromium (Cr): 24.0 – 26.0% • Nickel (Ni): 19.0 – 22.0% • Iron (Fe): Balance Applications: Suited for high-temperature environments with oxidizing, sulfurizing, or carburizing gases. Especially effective in boiler, furnace, and WHRB systems operating under cyclic thermal conditions. Uses • Installed on the inner arc of U-bend tubes in power plant boilers and superheaters exposed to slag and thermal stress • Protects curved tube bends in WHRBs, HRSGs, and reformers subjected to flue gas erosion and oxidation • Applied in heat exchangers and reactors operating in high-temperature and chemically active atmospheres • Used in furnace coils, metallurgical plants, and incinerators for protection from sulfur-laden and high-heat gas streams • Suitable for curved tube coils in petrochemical and process industries where scaling and corrosion are common Features • Excellent oxidation resistance – Performs effectively at continuous service temperatures up to 1100°C • Superior inner arc protection – Covers high-wear zones exposed to heat, slag, and turbulent gas flow • Enhanced thermal fatigue resistance – Designed for use in cyclic heating environments without distortion • Corrosion resistance – Withstands acid gases and sulfur-rich flue gases common in industrial combustion systems • Precision fitment – Fabricated to match specific tube sizes and bend radii for optimal protection and stability • Easy installation – Can be fixed using clamping, tack welding, or banding methods depending on system design Applications • power generation – Shields inner U-bend tubes in superheaters and reheaters from high-temperature erosion • waste heat recovery – Used in WHRBs and HRSGs to protect internal arcs against scaling and oxidation • petrochemical processing – Protects U-bend tubes in reformers and exchangers exposed to acidic gas streams • chemical industry – Ensures long-lasting performance in reactors and thermal processing equipment • metallurgical and furnace systems – Applied where high heat and slag exposure are routine Conclusion The 1Cr25Ni20Si2 U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – provides high-strength, heat-resistant shielding for the internal arcs of U-bend tubes operating in severe industrial environments. Its resistance to oxidation, corrosion, and thermal fatigue makes it a dependable solution for extending equipment life and performance under extreme conditions. For custom sizes, technical support, or pricing inquiries, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precisely engineered components used to safeguard boiler tubes, superheaters, and heat exchanger coils from erosion, scaling, thermal stress, and high-temperature corrosion. Their half-round construction enables quick and secure installation over straight or curved tube surfaces, offering long-term protection and minimizing maintenance in industrial heating systems, power plants, and petrochemical facilities. 1Cr18Ni9Ti U Type Inner Half Round Tube Shield The 1Cr18Ni9Ti U Type Inner Half Round Tube Shield is manufactured from a titanium-stabilized austenitic stainless steel grade, offering superior resistance to intergranular corrosion and oxidation at elevated temperatures. This grade is particularly effective in welded applications and thermal systems subjected to cycling and corrosive media. The inner U-type configuration is designed to shield the inside curvature of U-bend tubes, where turbulent gas flow, slag, and thermal concentration often cause accelerated wear and scaling. • Inner U Type Half Round Tube Shield – Designed to protect the internal arc of U-bend tubes from high-temperature scaling, slag impact, and turbulent gas erosion. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of 1Cr18Ni9Ti U Type Inner Half Round Tube Shields, offering durable, high-performance shielding solutions for critical thermal systems. Chemical Composition of 1Cr18Ni9Ti – Titanium-Stabilized Austenitic Stainless Steel • Carbon (C): ≤ 0.12% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 17.0 – 19.0% • Nickel (Ni): 8.0 – 11.0% • Titanium (Ti): Stabilized as required • Iron (Fe): Balance Applications: Ideal for welded and high-temperature systems exposed to oxidation, intergranular corrosion, and chloride-bearing flue gases. Uses • Protects inner arcs of U-bend tubes in superheaters and reheaters of thermal power plants • Installed in return bends of waste heat recovery boilers (WHRBs) and HRSGs facing slag and scale accumulation • Applied in curved tube sections in chemical reactors and heat exchangers exposed to acidic or oxidizing gases • Suitable for marine and coastal heating systems where chlorides and moisture are present • Used in food processing, metallurgical furnaces, and process plants requiring stable, high-temperature performance Features • Excellent intergranular corrosion resistance – Stabilized with titanium to prevent carbide precipitation • Inner arc protection – Shields high-stress areas from gas turbulence and heat-induced damage • High-temperature performance – Reliable up to 870°C in oxidizing environments • Custom fit – Fabricated to match specific tube diameters and bend radii for precise installation • Easy to install – Suitable for clamp-on, weld-on, or banding methods • Long service life – Reduces frequency of tube replacement and supports consistent thermal performance Applications • thermal power generation – Inner arc protection in U-bend tubes exposed to combustion gases and temperature fluctuations • petrochemical and fertilizer plants – Shields tube bends in reactors and reformers exposed to acidic gases • waste heat recovery – Guards inner surfaces of tube coils in WHRBs and HRSGs from scaling and corrosion • marine heat exchangers – Suitable for use in systems exposed to saltwater vapors and high humidity • industrial furnaces and incinerators – Provides internal bend protection under severe thermal cycling Conclusion The 1Cr18Ni9Ti U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – delivers robust and reliable protection for U-bend tubes operating in corrosive and high-temperature environments. With titanium stabilization and a custom-engineered fit, this shield ensures extended tube life, reduced wear, and optimized performance in industrial heating systems. For technical assistance, custom specifications, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are designed to protect heat exchanger, boiler, and superheater tubes from erosion, scaling, slag deposition, and corrosion under high-temperature operating conditions. These shields are widely used in industries such as power generation, petrochemical processing, waste heat recovery, and chemical manufacturing. Their half-round structure allows for quick installation over curved or straight tube sections, providing dependable protection and extending equipment lifespan without requiring major disassembly. SS 316L U Type Inner Half Round Tube Shield The SS 316L U Type Inner Half Round Tube Shield is fabricated from low-carbon austenitic stainless steel grade 316L. It offers superior corrosion resistance, particularly in chloride-rich or acidic environments, and improved weldability with reduced risk of intergranular corrosion after welding. The inner U-type configuration is specifically engineered to shield the inner arc of U-bend tubes—an area highly vulnerable to turbulence-induced erosion, scaling, and thermal fatigue. • Inner U Type Half Round Tube Shield – Designed to protect the inner curvature of U-bend tubes from flue gas turbulence, localized corrosion, and heat-induced scaling. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of SS 316L U Type Inner Half Round Tube Shields, providing durable and customizable shielding solutions for demanding thermal and corrosive applications. Chemical Composition of SS 316L – Low Carbon Austenitic Stainless Steel • Carbon (C): ≤ 0.035% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Nickel (Ni): 10.0 – 14.0% • Molybdenum (Mo): 2.0 – 3.0% • Iron (Fe): Balance Applications: Ideal for welded systems and high-temperature environments exposed to chlorides, acidic gases, or steam, where resistance to corrosion and thermal degradation is essential. Uses • Shields inner arcs of U-bend tubes in boilers, superheaters, and reheaters operating in corrosive and high-heat zones • Installed in return bends of waste heat recovery boilers (WHRBs) and HRSGs subjected to scaling and slag formation • Used in curved tube sections of steam reformers, condensers, and marine heat exchangers • Applied in chemical and fertilizer plants with exposure to acidic, chloride-rich, or humid gases • Suitable for welded assemblies where protection against intergranular corrosion is necessary Features • Excellent corrosion resistance – Enhanced performance in acidic, chloride-laden, and high-moisture environments • Low carbon content – Minimizes risk of intergranular corrosion after welding or high-temperature service • Inner bend protection – Shields areas affected by turbulence, localized heat, and erosion • High-temperature durability – Performs reliably in oxidizing environments up to 870°C • Custom fabrication – Tailored to match specific tube diameters and bend radii for a secure, gap-free fit • Easy installation – Suitable for clamp-on, banding, or weld-on mounting without requiring full system disassembly Applications • power generation – Inner U-type shields for protecting boiler and economizer bends in thermal power stations • petrochemical facilities – Guards internal tube bends exposed to chlorides and hot process gases in reformers • waste heat recovery systems – Applied to WHRBs and HRSGs for inner arc protection from flue gas scaling • chemical processing units – Used in reactors and exchanger coils to resist chemical and thermal corrosion • marine and offshore systems – Ensures long-term durability of U-bends exposed to saltwater-laden environments Conclusion The SS 316L U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a reliable and corrosion-resistant protective component designed for inner arc shielding in U-bend tubes operating under harsh thermal and chemical conditions. With its superior weldability, resistance to pitting, and high-temperature strength, it is ideal for critical service in energy, chemical, and marine applications. For technical support, custom specifications, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are engineered to provide robust protection for boiler tubes, superheaters, and heat exchangers operating under harsh thermal and corrosive conditions. Designed for installation over curved or straight tube sections, these shields help prevent erosion, slag accumulation, scaling, and high-temperature corrosion. Their half-round shape allows for quick and secure mounting, extending tube service life and minimizing unplanned maintenance in power plants, petrochemical facilities, and other high-temperature industrial systems. SS 316 U Type Inner Half Round Tube Shield The SS 316 U Type Inner Half Round Tube Shield is manufactured from molybdenum-bearing austenitic stainless steel grade 316, offering enhanced resistance to pitting, crevice corrosion, and chloride-induced attack. The inner U-type configuration is specifically designed to cover the internal arc of U-bend tubes, where gas turbulence and heat concentration tend to cause localized wear and scaling. This makes it an ideal choice for systems operating in corrosive, chloride-rich, or marine environments. • Inner U Type Half Round Tube Shield – Protects the internal curvature of U-bend tubes from high-temperature scaling, erosion, and corrosion due to turbulent gas flow and thermal cycling. Ladhani Metal Corporation is a reliable manufacturer, supplier, and exporter of SS 316 U Type Inner Half Round Tube Shields, offering precision-fabricated shielding solutions tailored to the needs of critical high-performance industries. Chemical Composition of SS 316 – Austenitic Stainless Steel with Molybdenum • Carbon (C): ≤ 0.08% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.045% • Sulfur (S): ≤ 0.030% • Silicon (Si): ≤ 1.00% • Chromium (Cr): 16.0 – 18.0% • Nickel (Ni): 10.0 – 14.0% • Molybdenum (Mo): 2.0 – 3.0% • Iron (Fe): Balance Applications: Best suited for environments with exposure to chlorides, acidic gases, or steam, where advanced corrosion resistance and heat performance are required. Uses • Protection of inner arcs of U-bend tubes in superheaters and reheaters exposed to flue gas turbulence • Installed in return bends of heat exchangers, condensers, and WHRBs where inner surfaces face scaling and erosion • Ideal for curved tube sections in petrochemical reactors, steam reformers, and coastal or offshore installations • Applied in high-temperature systems exposed to chloride-laden or acidic process gases • Used in chemical and fertilizer plants where welded tube bends are prone to localized corrosion Features • Superior corrosion resistance – Molybdenum content enhances resistance to pitting, crevice corrosion, and aggressive chemicals • Inner arc coverage – Designed specifically for areas affected by turbulence and localized heat attack • Excellent high-temperature performance – Maintains mechanical strength and oxidation resistance up to 870°C • Custom fitment – Precisely fabricated to match tube diameter and bend radius for secure installation • Versatile mounting – Installed using clamps, bands, or tack welding, without needing system disassembly • Long-term reliability – Reduces tube degradation, downtime, and maintenance in harsh service conditions Applications • power generation – Used in U-bend tubes of superheaters and economizers in chloride-containing flue gas environments • petrochemical industry – Shields tube bends in reformers and exchangers exposed to acidic gases and steam • waste heat recovery – Protects inner arcs of tube coils in WHRBs and HRSGs from scaling and corrosion • chemical processing – Ideal for tube protection in corrosive media with high moisture and heat • marine and coastal systems – Provides corrosion defense in return bends of heat exchangers exposed to salt-laden air Conclusion The SS 316 U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a high-performance shielding solution for protecting the inner curvature of U-bend tubes exposed to heat and corrosive environments. With its molybdenum-enhanced resistance and precision engineering, this shield is ideal for applications requiring superior durability, thermal stability, and corrosion protection. For custom dimensions, technical guidance, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are engineered to provide robust protection for boiler, superheater, and heat exchanger tubes against high-temperature erosion, slag deposition, scaling, and corrosive gas exposure. These shields are essential in power plants, petrochemical systems, and high-heat industrial environments where tubes are vulnerable to rapid degradation due to thermal cycling and particulate flow. The half-round design ensures quick installation over curved or straight tube sections without system disassembly. U Type Inner Half Round Tube Shield The U Type Inner Half Round Tube Shield is specially designed to protect the inner curvature of U-bend tubes, which often experiences high levels of turbulence, localized corrosion, and scaling due to gas redirection and mechanical stress. Inner shields are commonly paired with outer shields for full bend protection and are manufactured in a wide range of stainless steel and high-temperature alloy grades, customized to specific environmental and system requirements. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of U Type Inner Half Round Tube Shields in various material grades, offering tailored protection solutions for high-temperature and corrosive conditions across multiple industries. Available Grades • SS 304 – General-use stainless steel with good corrosion and heat resistance • SS 304L – Low-carbon version for improved weldability and reduced carbide precipitation • SS 316 – Molybdenum-added alloy with excellent resistance to pitting and chlorides • SS 316L – Low-carbon alternative for superior corrosion resistance in welded environments • SS 310 – Austenitic high-temperature steel with excellent oxidation resistance • SS 310S – Low-carbon SS 310 for better thermal fatigue performance • SS 410 – Martensitic stainless steel with good strength and abrasion resistance • SS 420 – High-hardness martensitic grade ideal for erosion-prone zones • SS 430 – Ferritic grade for moderate corrosion and oxidation resistance • 1Cr13 – Martensitic stainless steel offering mechanical protection and heat resistance • 1Cr18Ni9Ti – Titanium-stabilized grade offering resistance to intergranular corrosion • Cr23Ni13 – High-temperature alloy with excellent oxidation and scaling resistance • Cr25Ni20 – High-performance grade for extreme thermal and oxidizing conditions • 1Cr25Ni20Si2 – Heat-resistant alloy with silicon for improved scale resistance • 1Cr20Ni14Si2 – Alloy for thermal fatigue protection and oxidizing environments Applications • Inner arc protection in U-bend tubes of boilers, superheaters, and reheaters • Shielding internal curves of tubes in waste heat recovery boilers (WHRBs) and HRSGs • Corrosion and scale defense for inner tube arcs in petrochemical and steam reforming units • Inner surface protection in furnace coils, reformers, and incinerators • Installed in chemical plants and thermal systems prone to turbulent flue gas exposure Features • Focused inner arc protection – Guards the most corrosion- and scale-prone surface of U-bend tubes • Material flexibility – Available in multiple grades for varied thermal, mechanical, and chemical requirements • Excellent thermal resistance – Withstands extreme temperatures depending on material (up to 1150°C+) • Precise fit – Custom-fabricated to match exact tube dimensions and bend radii • Simple installation – Mounted using clamps, stainless bands, or welding techniques • Dual-shield pairing – Can be combined with outer shields for complete U-bend coverage • Long-lasting performance – Enhances tube reliability and reduces maintenance in high-wear zones Applications • power generation – Protects U-bend inner surfaces in superheaters and economizers from flue gas turbulence • petrochemical plants – Shields inside arcs in reformers and heaters exposed to chlorides and acidic gases • waste heat systems – Installed in HRSGs and WHRBs to prevent slag and oxidation on internal bends • chemical industries – Suitable for reactors and high-temperature exchangers handling corrosive media • cement and metallurgy – Used in systems exposed to flame, dust, and oxidizing atmospheres Conclusion The U Type Inner Half Round Tube Shield by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a precision-engineered solution for protecting the inner arc of U-bend tubes against corrosion, scale formation, and thermal damage. Available in a wide range of stainless steels and high-temperature alloys, these shields provide durable, customizable, and easy-to-install protection for critical components in power, chemical, and thermal processing systems. For custom sizes, technical assistance, or quotations, please contact Ladhani Metal Corporation.

Half Round Tube Shield Half Round Tube Shields by Ladhani Metal Corporation are precision-designed components used to protect boiler, superheater, and heat exchanger tubes from erosion, slag accumulation, scaling, and high-temperature oxidation. These shields are essential for industrial systems exposed to intense thermal cycling, high-velocity flue gases, and corrosive atmospheres. Their half-round form ensures quick and secure installation over curved or straight tube surfaces, significantly enhancing tube durability and reducing downtime. 1Cr20Ni14Si2 U Type Outer Half Round Tube Shield The 1Cr20Ni14Si2 U Type Outer Half Round Tube Shield is made from a high-performance austenitic stainless steel alloy containing 20% chromium, 14% nickel, and approximately 2% silicon. This alloy provides excellent resistance to oxidation, high-temperature corrosion, and thermal fatigue, especially in oxidizing and carburizing environments. The outer U-type design is specifically intended to protect the outer arc of U-bend tubes in boilers, reformers, and heat exchangers, where flame, gas flow, and slag buildup cause the most wear. • Outer U Type Half Round Tube Shield – Shields the outer curvature of U-bend tubes from flame impingement, gas erosion, slag attack, and thermal scaling. Ladhani Metal Corporation is a leading manufacturer, supplier, and exporter of 1Cr20Ni14Si2 U Type Outer Half Round Tube Shields, offering custom-built shielding solutions for critical high-temperature and industrial systems. Chemical Composition of 1Cr20Ni14Si2 – Austenitic Heat-Resistant Stainless Steel • Carbon (C): ≤ 0.10% • Manganese (Mn): ≤ 1.50% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): 1.50 – 2.50% • Chromium (Cr): 19.0 – 21.0% • Nickel (Ni): 13.0 – 15.0% • Iron (Fe): Balance Applications: Best suited for high-temperature, oxidizing environments in power generation, chemical processing, and furnace systems where excellent thermal and scaling resistance are required. Uses • Outer arc protection for U-bend tubes in superheaters and reheaters in thermal power plants • Shields return bends in heat exchangers and steam reformers exposed to hot gases and flame • Used in waste heat recovery boilers (WHRBs) and HRSGs to prevent surface oxidation and slag damage • Suitable for petrochemical and chemical reactors operating under oxidizing or mildly carburizing conditions • Applied in high-temperature industrial furnaces, incinerators, and reforming equipment Features • Excellent high-temperature resistance – Withstands service temperatures up to 1100°C with minimal deformation or scaling • Oxidation and corrosion resistance – High Cr-Ni-Si composition forms a stable oxide layer for prolonged exposure protection • Outer bend coverage – Provides critical protection for the most exposed and erosion-prone section of U-bend tubes • Custom fabrication – Manufactured to match exact tube radius and diameter, ensuring a precise and stable fit • Easy installation – Secured with clamps, tack welds, or stainless steel banding without disassembly • Long-lasting performance – Enhances operational life and minimizes costly tube replacements in aggressive environments Applications • thermal and power generation – Protects outer U-bend tube surfaces from slag, soot, and flue gas corrosion • petrochemical and refining – Shields return bends in reformers and heaters exposed to oxidizing and sulfur-rich gases • waste heat recovery – Guards outer tube arcs in WHRBs and HRSGs against scaling and erosion • metallurgy and cement processing – Used in high-temperature pipelines and ducts in furnaces and kilns • process heating systems – Ideal for environments involving intense flame exposure and cyclic thermal loads Conclusion The 1Cr20Ni14Si2 U Type Outer Half Round Tube Shield by Ladhani Metal Corporation—manufacturer, supplier, and exporter—is a highly durable, heat-resistant shielding solution for protecting U-bend tube outer surfaces in extreme industrial environments. With superior resistance to oxidation, scaling, and thermal fatigue, it ensures long-term reliability and efficiency in power plants, reformers, and furnace systems. For technical consultation, custom orders, or quotations, please contact Ladhani Metal Corporation