Half Round Tube Shield Half Round Tube Shields from Ladhani Metal Corporation are durable, precisely fabricated components used to protect boiler tubes from erosion, scaling, and corrosion caused by flue gas flow and particulate impact. Their half-round, semi-cylindrical structure is designed to conform closely to tube surfaces, especially in areas subjected to repeated thermal cycling or mechanical wear. These shields are extensively applied in boilers, heat exchangers, and waste heat recovery systems. 1Cr25Ni20Si2 Half Round Tube Shield for LTSH Tube The 1Cr25Ni20Si2 Half Round Tube Shield is manufactured from a high-performance chromium-nickel-silicon alloy designed for elevated-temperature service. With approximately 25% chromium, 20% nickel, and added silicon content, this alloy exhibits superior resistance to oxidation, thermal fatigue, and carburization. Its mechanical stability under high-temperature operation makes it a preferred material for protective applications in Low Temperature Superheater (LTSH) zones. The Low Temperature Superheater (LTSH) is a section in a boiler where saturated steam from the steam drum is superheated to a moderately higher temperature before entering the high-temperature superheater stages. Positioned in areas with relatively lower flue gas temperatures, the LTSH helps improve thermal efficiency and reduces moisture content in steam. Due to constant exposure to abrasive flue gases and ash, LTSH tubes are prone to wear and require protective shielding, such as half round tube shields, to extend service life. Ladhani Metal Corporation is a trusted manufacturer, supplier, and exporter of 1Cr25Ni20Si2 Half Round Tube Shields, offering high-performance shielding solutions tailored for harsh, heat-intensive industrial environments. Chemical Composition of 1Cr25Ni20Si2 – Chromium-Nickel-Silicon Heat-Resistant Steel • Carbon (C): ≤ 0.10% • Manganese (Mn): ≤ 2.00% • Phosphorus (P): ≤ 0.035% • Sulfur (S): ≤ 0.030% • Silicon (Si): 1.5 – 2.5% • Chromium (Cr): 24.0 – 27.0% • Nickel (Ni): 19.0 – 22.0% • Iron (Fe): Balance Applications: Suitable for high-temperature steam systems, where resistance to flue gas corrosion, thermal oxidation, and mechanical fatigue is essential. Uses • Protects LTSH tubes in thermal power plants from scaling and soot-induced wear • Shields heat exchanger tubes from low-temperature corrosive gases and ash deposition • Used in boilers and HRSGs exposed to fluctuating temperature and combustion by-products • Suitable for high-wear areas in biomass boilers and incineration systems • Enhances operational life of reheater and superheater coil sections Features • High thermal stability – Withstands temperature fluctuations without structural deformation • Excellent oxidation and carburization resistance – Ideal for extended high-temperature exposure • Custom fit – Designed according to specific tube radii and coil geometries for accurate alignment • Reduced maintenance – Shields tubes from damage, minimizing downtime and repair costs • Versatile installation – Compatible with weld-on, clamp-on, and banding installation techniques • Long service life – Resistant to scaling and degradation in heat-intensive environments Applications • power generation boilers – Provides long-term protection for LTSH coils in flue gas zones • WHRBs and HRSGs – Used in low-temperature convection sections to counteract erosive gas flow • chemical and refining industries – Prevents corrosion in heat exchangers handling acidic media • marine steam systems – Protects low-temperature sections exposed to salt-laden air and gases • waste-to-energy plants – Shields boiler tubing from high-volume particulate streams Conclusion The 1Cr25Ni20Si2 Half Round Tube Shield for LTSH Tube by Ladhani Metal Corporation – manufacturer, supplier, and exporter – is a high-performance component designed for superior protection of boiler tubes in corrosive and thermally aggressive environments. It ensures durability, thermal resistance, and long-term reliability in LTSH and similar service applications. For specifications, custom fabrication, or bulk orders, contact Ladhani Metal Corporation.

DIN 2545 duplex flanges are designed to provide exceptional strength and corrosion resistance in demanding industrial applications. Ladhani Metal Corporation offers these high-quality flanges made from duplex stainless steel, which combines the best features of both austenitic and ferritic structures. This unique material provides superior resistance to pitting, crevice corrosion, and stress corrosion cracking, making it ideal for use in harsh environments. With a pressure rating of PN 40, these flanges are capable of handling pressures up to 40 bar, ensuring safe and reliable performance in industries such as chemical processing, oil and gas, marine, and offshore platforms. Types of DIN 2545 Duplex Flanges: Flat Face Flanges (FF) – These flanges have a flat surface that facilitates a uniform distribution of the sealing force, making them ideal for low-pressure applications or systems where a secure seal is essential. Raised Face Flanges (RF) – Featuring a raised face around the bolt holes, these flanges provide a higher sealing pressure, ensuring a more reliable seal, especially in higher-pressure environments. Ring-Type Joint (RTJ) Flanges – Designed with a groove for a metal sealing ring, these flanges are suitable for use in applications requiring high pressure and high temperature resistance. Grades and Chemical Composition: -Duplex 2205 (UNS S32205) Chemical Composition: Cr: 22%, Ni: 5-6%, Mo: 3%, N: 0.14-0.2%, Fe: balance Duplex 2205 is the most common duplex stainless steel grade. It offers excellent corrosion resistance in chloride environments, making it suitable for applications like seawater, chemical, and petrochemical processing. The combination of austenitic and ferritic phases gives Duplex 2205 higher strength compared to austenitic stainless steels, along with improved resistance to pitting and stress corrosion cracking. Super Duplex 2507 (UNS S32750) Chemical Composition: Cr: 25%, Ni: 7%, Mo: 4%, N: 0.27%, Fe: balance Super Duplex 2507 is a higher alloy version of Duplex 2205, offering superior resistance to chloride stress corrosion cracking, pitting, and crevice corrosion. It is used in more aggressive environments, such as offshore oil and gas applications, where the material must withstand high pressures and corrosive conditions. Its higher molybdenum and nitrogen content enhances its performance in severe environments. PN 40 Pressure Rating: The "PN" in DIN 2545 refers to the pressure rating, and PN 40 indicates that the flange is designed to handle pressures up to 40 bar. This ensures that the flange is robust and reliable under high-pressure conditions, maintaining secure and leak-proof connections in critical applications. Applications: Oil and Gas Industry: These flanges are widely used in offshore and onshore pipelines, pressure vessels, and other critical infrastructure in oil and gas exploration, extraction, and transportation. Chemical and Petrochemical Industry: Due to their excellent resistance to corrosion, especially in acidic or chloride-rich environments, they are ideal for use in reactors, heat exchangers, and pipelines handling chemicals and petrochemicals. Marine and Offshore Applications: Duplex flanges are highly resistant to seawater corrosion, making them ideal for use in marine environments, such as shipbuilding, offshore rigs, and seawater cooling systems. Water Treatment Plants: These flanges are used in systems that handle aggressive water environments, ensuring durability and long service life in water and wastewater treatment applications. Power Generation: In power plants, these flanges are used in steam lines, cooling systems, and heat exchangers, where strength, corrosion resistance, and high-pressure capabilities are critical. Pharmaceutical Industry: These flanges are used in systems requiring sanitary conditions and resistance to aggressive cleaning solutions, such as in the transportation of chemicals or in reaction vessels. Key Benefits of Duplex Flanges (PN 40): Exceptional strength and corrosion resistance. Resistance to pitting and crevice corrosion. Excellent performance in harsh environments. Cost-effective compared to higher-grade materials for similar applications. DIN 2545 Duplex Flanges (PN 40) are a reliable choice for high-pressure applications in industries that demand both high performance and durability. #din2545 #din2545flanges #din2545duplexflanges #flanges

DIN 2544 Monel flanges are flanges manufactured according to the DIN 2544 standard, specifically designed for use with Monel alloys. Monel is a high-performance nickel-copper alloy known for its outstanding corrosion resistance, particularly in seawater, acids, and alkaline environments. These flanges are widely used in industries such as marine, chemical processing, petrochemical, and other applications that require resistance to aggressive media and high temperatures. Key Features: Material: Monel alloys (typically Monel 400 and Monel K-500). Pressure Rating (PN 25): These flanges are rated for pressure class PN 25, meaning they can handle pressures up to 25 bar (2500 kPa). Corrosion Resistance: Monel alloys offer excellent resistance to corrosion in harsh environments such as seawater and acidic solutions, making them ideal for marine and chemical applications. Strength: Monel alloys exhibit high strength and toughness, retaining their mechanical properties even in elevated temperature environments. Temperature Resistance: Monel alloys maintain integrity and strength even in high-temperature conditions, making them suitable for demanding applications. Types of DIN 2544 Monel Flanges: Weld Neck Flange (WN): These flanges are ideal for high-pressure applications where a reliable, leak-proof connection is required. The neck is welded to the pipe to create a strong joint. Slip-On Flange (SO): These flanges are easy to install by slipping over the pipe, then welding both inside and outside for a secure connection. Blind Flange (BL): Used to seal the ends of pipes, vessels, or other openings, providing a leak-tight closure. Threaded Flange (TH): These flanges are screwed onto the pipe without welding, making them easier to install and remove when needed. Socket Weld Flange (SW): Designed for smaller pipe sizes, where the pipe is inserted into the socket and welded into place for a strong, secure joint. Grades of Monel: Monel 400: A nickel-copper alloy containing 63% nickel and 29% copper, Monel 400 offers excellent resistance to seawater and other corrosive environments. It is commonly used in marine and chemical processing applications. Monel K-500: This alloy is similar to Monel 400 but with added titanium and aluminum for improved strength and hardness. It is used in high-stress environments such as aerospace and marine applications. Pressure Rating (PN 25): PN 25 means the flange is rated to withstand pressures of up to 25 bar (2500 kPa), making it ideal for moderate to high-pressure applications. Summary: DIN 2544 Monel flanges are corrosion-resistant components made from Monel alloys, ideal for use in industries like marine, chemical processing, and petrochemical. Ladhani Metal Corporation offers a variety of Monel flanges, including weld neck, slip-on, blind, threaded, and socket weld types, rated for pressures up to PN 25. With a strong focus on quality and customer service, Ladhani Metal Corporation provides high-performance solutions for industries worldwide.

ladhani metal corporation is supplier and exporter of BS S524 sheet , plate , coil , flat bar , circular plate , plate flanges , farma , laser cutting design sheet , waterjet cutting design sheet.BS S524 is the basic austenitic 18/8 steel stabilised by Titanium or additions. These grades are used because they are not sensitive to intergranular corrosion after heating within the carbide precipitation range of 425-850°C.BS S524 is the grade of choice for applications in the temperature range of up to about 900°C, combining high strength, resistance to scaling and phase stability with resistance to subsequent aqueous corrosion. Cold Bending : It has excellent cold working properties and cold bending can generally be carried out without too much difficulty. Hot Bending : Hot bending should be performed at 950oC - 1100Oc. Corrosion Resistance : it similar resistance to general corrosion in most media as 304, but not as good as 316. Stress Corrosion Cracking : it has similar resistance to stress corrosion cracking as 304, but not as good as 316. Pitting Corrosion / Crevice Corrosion : It has similar resistance to pitting and crevice corrosion as 304, but not as good as 316. Intergranular Corrosion : it has better resistance to intergranular corrosion than most of the standard 300 grades other than the low carbon types 304L, 316L and 317L due to its titanium content.N.B. Forging : Heat uniformly to 1150oC - 1200oC Machining: It is more difficult to machine than most of the standard austenitic stainless steels, due to its titanium addition. Our Domestic reach is unlimited and we supply to this following cities Ahmedabad, Amritsar, Aurangabad, Bangalore, Bhopal, Chandigarh, Chennai, Coimbatore, Dhanbad, Faridabad, Ghaziabad, Guwahati, Gwalior, Howrah, Hyderabad, Indore, Jabalpur, Jaipur, Jodhpur, Kanpur, Kolkata, Kota, Lucknow, Ludhiana, Madurai, Meerut, Mumbai, Nagpur, Nashik, Navi Mumbai, New Delhi, Patna, Pune, Raipur, Rajkot, Ranchi, Solapur, Srinagar, Surat, Thane, Vadodara, Varanasi, Vijayawada, Visakhapatnam, Hubballi, Tiruchirappalli, Bareilly, Moradabad, Mysore, Gurgaon, Aligarh, Jalandhar, Bhubaneswar We export to following Countries: Russia, Canada, United States, China, Brazil, Australia, Argentina, Kazakhstan, Algeria, Denmark, Saudi Arabia, Mexico, Indonesia, Iran, Mongolia, Peru, South Africa, Colombia, Ethiopia, Bolivia, Egypt, Venezuela, Turkey, Chile, Myanmar, France, Ukraine, Madagascar, Botswana, Kenya, Thailand, Spain, Sweden, Uzbekistan, Morocco, Paraguay, Zimbabwe, Norway, Japan, Germany, Republic of the Congo, Finland, Vietnam, Malaysia, Poland, Oman, Italy, Philippines, Ecuador, New Zealand, United Kingdom, Guinea, Uganda, Nepal, Bangladesh.

Product Name: Titanium Plate Standard: ASTM B265 Material: Gr1 Unit Price: $15usd/kg-$48usd/kg Thickness: 0.5-100mm Length: 500-6000mm Or As You Require Width: 500-1000mm Or As You Require

Product Name: Titanium racks for aluminum anodizing Material: Gr1, Gr2 Application: Electroplating, anodizing etc. Size: Customized Surface: Polished Type : Titanium racks / Titanium Jigs Dimenstion and shape : Customized, as customer's drawings Finishing : Polished Material : Pure Titanium(gr1 gr2) Condition : New Application : Electroplating, anodizing etc Color : Sliver.Grey Features : Anti-corrosion, good elasticity, smooth surface, dustproof, strong structure, good quality, fine surface We provide various titanium plating rack jigs. These ranges of jigs are available in different sizes to maximize customer satisfaction. Also, these jigs are provided at very affordable prices. Our technique can adapt jigs to the most suitable parts and materials, so that the product has higher durability and strength. Our production system reduces the entrainment of impurities and liquids between tanks and improves the passage of current, as well as its uniform distribution throughout the whole rack. The continuous availability of raw materials, laser cutting machines, folding and automatic welding machines makes our products the most competitive in the market and able to complete tasks within very tight deadlines. Chemical composition (Wt%) ASTM No. Fe max O max N max C max H max Pd Al Bal Grade 1 0.2 0.18 0.03 0.1 0.015 - - Ti Grade 2 0.3 0.25 0.03 0.1 0.015 - - Ti Physical Properties (Min) ASTM Grade Alloy Composition Tensile Strength Yield Strength Elongation min % ksi Mpa ksi Mpa Grade 1 Unalloyed Ti ("Pure") 35A -CP1 35 240 25 170 30 Grade 2 Unalloyed Ti ("Pure") 50A -CP2 58 400 40 275 25

Product name:Titanium Sheet Unit price:$15.5-$36.9/kg Material: Titanium Grade 5 (Ti6al4v) Standard: ASTM/ASME B265 AMS 4911 ASTM F136 Demension: Thickness*1000*2000mm Thickness*3000*6000mm (Standard size); Thickness: 0.5mm; 0.8mm; 1.0mm; 1.2mm; 1.5mm; 2.0mm; 3.0mm; 4.0mm ......40mm etc br>Technique : Rolled Status: Annealed(M) MTC: EN10204.3.1 certificate MOQ : 10kgs Applications : Petroleum ,chemical industry, Marine, medical Package:Standard export packaging, inside foam film and pearl cotton protection, outside fumigation-free plywood case. Customized size welcome. Hot rolled titanium plate Titanium plate gr5 Grade 5 titanium plate titanium alloy plate Ti6al4v plate Grade 5 titanium is one of the most commonly used alloys in titanium industry, accounting for 50% of the world titanium consumption. Also known as Ti-6Al-4V (or ti6-4), this name refers to its main chemical composition of 90% titanium, 6% aluminum, 4% vanadium, 0.25% (maximum) iron and 0.2% (maximum) oxygen. It has almost the same high corrosion resistance as pure titanium, but has better strength, low elastic modulus, good weldability and heat treatment. The addition of aluminum and vanadium improves the hardness and physical and mechanical properties of the alloy. Product name:Titanium Sheet ,grade 5 titanium sheet ,titanium alloy sheet,10mm titanium sheet,5mm titanium sheet,gr5 titanium sheet,6Al4V sheet, Ti6Al4V titanium sheet,Titanium sheet plate price per kg Material: Titanium Grade 5 (Ti6al4v) Standard: ASTM/ASME B265, AMS 4911, ASTM F136 Demension: Thickness*1000*2000mm Thickness*3000*6000mm (Standard size); Thickness: 0.5mm; 0.8mm; 1.0mm; 1.2mm; 1.5mm; 2.0mm; 3.0mm; 4.0mm ......40mm etc Technique : Rolled Status: Annealed(M) MTC: EN10204.3.1 certificate Grade 5 (Ti6Al4V) titanium sheet/plate Chemical compositions(weight%,<=) Ti Al V Fe C Remainder 5.5-6.75 3.5-4.5 0.30 0.08 N H O Other(total) 0.05 0.015 0.2 0.4 Physical properties(>=) Σb Tensile Strength (Mpa) σr0.2 Yield Strength (Mpa) δL0+50mm Elongation (%) ψ Reduction of area (%) 895 830 12 25

Product Name: Titanium Screw Standard: DIN933 DIN934 Material: Gr2 Unit Price: $0.5usd/pc-$3.2usd/pc Head Type: Hexagon Head Surface: Polished Technique: CNC Machined, Forged MOQ: 200pcs

Product Name: Titanium anodizing jigs Material: Gr1, Gr2 Application: Electroplating, anodizing etc. Size: Customized Surface: Polished What is a titanium anodizing jigs/titanium jig/titanium rack? Titanium installation in electroplating production is mainly conducted, supported and fixed parts, pendants and electrode connections, so that the current is more evenly transmitted to the parts for electroplating. In some cases, the uniform distribution of the coating can also be compensated by a suspension because the solution properties limit it. Item Anodizing Tianium jig/rack Size Customsed size Material Titanium Size(mm)in Bulk Stock 20/30/50 teeth Can be customized Grade Gr1 Gr2 Performance Corrosion-resisant Chemical composition (Wt%) ASTM No. Fe max O max N max C max H max Pd Al Bal Grade 1 0.2 0.18 0.03 0.1 0.015 - - Ti Grade 2 0.3 0.25 0.03 0.1 0.015 - - Ti Physical Properties (Min) of Titanium Anodizing Jigs ASTM Grade Alloy Composition Tensile Strength Yield Strength Elongation min % ksi Mpa ksi Mpa Grade 1 Unalloyed Ti ("Pure") 35A -CP1 35 240 25 170 30 Grade 2 Unalloyed Ti ("Pure") 50A -CP2 58 400 40 275 25